Votos - 4, Puntuación media: 4.5
(
)
)
|
Resumen del manual
See FIGURE 1. • Remove the bottom of the front SHROUD & rear SHROUD by removing the four 3/8” X 1” BUTTON HEAD CAP SCREWS. See !IMPORTANT! • IF THE 832 LEG PRESS OPTION IS INSTALLED PROCEED TO PAGE 14. • IF THE 445 WEIGHT STACK OPTION IS INSTALLED PROCEED TO PAGE 27. • IF THE 832 LEG PRESS OPTION & 445 WEIGHT STACK OPTION ARE INSTALLED PROCEED TO PAGE 35. • IF NO OPTIONS ARE INSTALLED CONTINUE TO PAGE 3. 2 STEP 3 • Remove the three 1/4” CAP NUTS and each TENSION CORD from the TOP BOOM as shown in FIGURE 3. STEP 4 • Remove the three TENSION CORDS from the D-RING by removing the three KEYHOLE CLEVIS, CLEVIS PINS, and COTTER PINS as shown in 4. 3 STEP 5 • Remove the 3/8 X 2” BOLT, two 3/8” WASHERS, one 2-7/8” L-BRACKETS, one 4-1/2” PULLEY, and one 3/8” LOCK NUT from the upper flat on the BASE as shown in FIGURE 5. • SECURELY assemble the previously removed 4-1/2” PULLEY to the BASE using one 3/8 X 2-1/2” BOLT (1), two previously removed 3/8” WASHERS, one previously removed 2-7/8” L-BRACKET, one SWIVEL SNAP (3), one 3/8” HEX NUT (8), and one previously removed 3/8” LOCK NUT. See FIGURE 6. 4 STEP 7 • Position two 3/8 X 1/2” SPACERS (2) inside the bracket on the BASE and slide one 3/8” THREADED SHAFT (9) through the bracket. See FIGURE 7. • Assemble two 3/8” HEX NUTS (8), two SWIVEL SNAP (3), and two 3/8” LOCK NUTS (7) to the 3/8” THREADED SHAFT (9) as shown in FIGURE 7. 5 • Remove the 3/8 X 2-1/4” BOLT, two 3/8” WASHERS, one 3/8” LOCK NUT, and 3-1/2” PULLEY from the bracket on the TOP BOOM as shown in FIGURE 8. • SECURELY assemble the previously removed 3 -1/2” PULLEY to the bracket on the TOP BOOM using one 3/8” THREADED SHAFT (9) , two previously removed 3/8” WASHERS, one 2” PULLEY (5), one 3/8” HEX NUT (8), one previously removed 3/8” LOCK NUT, and one 3/8” LOCK NUT (7). See FIGURE 9. 6 STEP 10 • Position two 3/8 X 1/2” SPACERS (2) inside the rear bracket of the TOP BOOM and slide one 3/8” THREAD SHAFT (9) through the bracket. See FIGURE 10. • SECURELY assemble two 2” PULLEYS (5) to the rear bracket on the TOP BOOM using one 3/8” THREADED SHAFT (9), two 3/8” WASHERS, two 3/8” HEX NUTS (8), and two 3/8” LOCK NUTS (7) as shown in FIGURE 10. STEP 11 • Assemble three 72” ELASTIC CORDS to the KEYHOLE CLEVIS as shown in FIGURE 11. 7 • Assemble the 22” ELASTIC CORD (4) from the PRESS CABLE around the 2” PULLEY (5) in the TOP BOOM as shown in FIGURE 12. 8 • Assemble the 22” ELASTIC CORD (4) from the LEG CABLE around the 2” PULLEY (5) in the TOP BOOM as shown in FIGURE 13. 9 • Assemble the 22” ELASTIC CORD (4) from the LAT CABLE around the 2” PULLEY (5) in the TOP BOOM as shown in FIGURE 14. 10 • Assemble the ELASTIC CORD (4) from the PRESS CABLE to the SWIVEL SNAP (3) on the BASE as shown in FIGURE 15. 11 • Assemble the ELASTIC CORDS (4) from the LAT & LEG CABLES to the corresponding SWIVEL SNAPS (3) on the BASE as shown in FIGURE 16. 12 STEP 17 • SECURELY attach the top of the front SHROUD (with label) & rear SHROUD to the TOP BOOM using the four previously removed 3/8” X 1” BUTTON HEAD CAP SCREWS. See FIGURE 17. STEP 18 • SECURELY attach the bottom of the front SHROUD (with label) & rear SHROUD to the TOP BOOM using the four previously removed 3/8” X 1” BUTTON HEAD CAP SCREWS. See FIGURE 18. The installation of the 426103 Elastic Cord Conversion Kit is complete. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714. 13 425103 with 832 LEG PRESS OPTION INSTALLED • If the 445 WEIGHT STACK OPTION IS INSTALLED PROCEED TO PAGE 27. • If the 832 LEG PRES S OPTION & 445 WEIGHT STACK OPTION ARE INSTALLED PROCEED TO PAGE 3 5. • Remove the 1/4” CAP NUTS and each TENSION CORD from the TOP BOOM as shown in FIGURE 3. 14 STEP 4 • Remove the TENSION CORDS, CLEVIS PINS and COTTER PINS as shown in FIGURE 4. 15 • Remove two 3/8 X 2” BOLTS, four 3/8” WASHERS, two 2-7/8” L-BRACKETS, two 4-1/2” PULLEYS, and two 3/8” LOCK NUTS from the upper flats on the BASE as shown in FIGURE 5. STEP 6 • SECURELY assemble the previously removed 4-1/2” PULLEY S to the BASE using two 3/8 X 2-1/2” BOLTS (1), four previously removed 3/8” WASHERS, two previously removed 2-7/8” L-BRACKETS, two SWIVEL SNAPS (3), two 3/8” HEX NUTS (8), and two previously removed 3/8” LOCK NUTS. See FIGURE 6. 16 • Remove one 3-1/2” PULLEY, one 3/8 X 2” BOLT, two 3/8” WASHERS and one 3/8” LOCK NUT from the BASE as shown in FIGURE 7. • Assemble two 3/8” HEX NUTS (8), two SWIVEL SNAP (3), one previously removed 3 -1/2” PULLEY, one previously removed 3/8” LOCK NUT, and one 3/8” LOCK NUT (7) to the 3/8” THREADED SHAFT (9) as shown in FIGURE 8. 17 • Remove the 3/8 X 2-1/4” BOLT, two 3/8” WASHERS, one 3/8” LOCK NUT, and 3-1/2” PULLEY from the bracket on the TOP BOOM as shown in FIGURE 9. • SECURELY assemble the previously removed 3 -1/2” PULLEY to the bracket on the TOP BOOM using one 3/8” THREADED SHAFT (9) , two previously rem...