Votos - 4, Puntuación media: 3.5
(
)
)
|
Resumen del manual
If you have additional questions, please call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please mention the product model number and serial number when calling. The model number is RBEX39010. The serial number can be found on a decal attached to the exercise cycle (see the front cover of this manual). Before reading further, please familiarize yourself with the parts that are labeled in the drawing below. Pulse Sensor Handlebar Water Bottle Holder (Bottle not included) FRONT BACK Seat Backrest Seat Knob Side Shield Leveling Pad Wheel Pedal/Strap Console Book Holder Seat Handle RIGHT SIDE ASSEMBLY Assembly requires two persons. Place all parts of the exercise cycle in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed. Assembly requires the included tools and your own adjustable wrench . Use the part drawings below to identify the small parts used in assembly. The number in parenthesis below each drawing refers to the key number of the part, from the PART LIST on page 14. The second number refers to the quantity used in assembly. Note: Some small parts may have been pre-attached for shipping. If a part is not in the parts bag, check to see if it has been pre-assembled. M10 x 75mm Carriage Bolt (72)–2 M8 x 25mm Button Screw (27)–4 M8 Split Washer (70)–4 M10 Nylon Locknut (45)–4 M8 Flat Washer (18)–4 M8 x 19mm Button Bolt (43)–4 M8 Nylon Locknut (56)–4 M6 Washer (25)–6 M6 x 16mm Hex Screw (29)–4 M6 x 38mm Hex Screw (78)–4 M10 x 82mm Carriage Bolt (63)–2 M6 x 16mm Screw (85)–2 M4 x 16mm Screw (90)–4 4 1. Identify the Front Stabilizer (2), which has Wheels (75) near its ends. Attach the Front Stabilizer to the front of the Frame (1) with two M10 x 75mm Carriage Bolts (72) and two M10 Nylon Locknuts (45). Make sure that the Front Stabilizer is turned so the Wheels are not touching the floor. 2. Attach the Rear Stabilizer (3) to the rear of the Frame (1) with two M10 x 82mm Carriage Bolts (63) and two M10 Nylon Locknuts (45). 3. While a second person holds the Handlebar Post (6) near the Frame (1) as shown, connect the Upper Wire Harness (16) to the Lower Wire Harness (77). Carefully slide the Handlebar Post (6) onto the Frame (1); be careful to avoid pinching the Wire Harnesses (16, 77). Attach the Handlebar Post to the Frame with four M8 x 25mm Button Screws (27) and four M8 Split Washers (70). 4. Connect the two Pulse Wires (86) to the two wires extending from the Console (9). Next, connect the Upper Wire Harness (16) to the back of the Console. Insert all wires into the Handlebar Post (6). Attach the Console (9) to the Handlebar Post (6) with four M4 x 16mm Screws (90). Be careful to avoid pinching the wires. 1 2 75 1 45 72 75 2 3 63 45 1 45 3 6 27 27 70 1 16 77 70 4 9 86 16 Console Wires 6 90 5 6 5. Attach the Seat (12) to the Seat Carriage (11) with four M6 x 16mm Hex Screws (29) and four M8 Flat Washers (18). 6. Attach a Seat Handle (14) to the Seat Carriage (11) with two M8 x 19mm Button Bolts (43) and two M8 Nylon Locknuts (56). Attach the other Seat Handle (14) to the Seat Carriage (11) in the same way. 7. Attach the Backrest (13) to the Seat Carriage (11) with four M6 x 38mm Hex Screws (78) and four M6 Washers (25). 43 14 14 56 11 13 25 11 25 78 5 6 7 8. Pull the seat knob and slide the Seat Carriage (11) onto the Seat Rail (7). Refer to the inset drawing. Hold the Bumper Axle (82) inside of the Seat Rail (7). Attach the two Bumpers (84) to the ends of the Bumper Axle with two M6 x 16mm Screws (85) and two M6 Washers (25) as shown. Press the Seat Rail Endcap (23) into the end of the Seat Rail. 11 Knob 7 8 12 11 29 29 18 23 82 85 85 84 84 25 25 7 9. Firmly tighten the four M8 x 31mm Button Screws (80) in the Seat Carriage (11). Pull the seat knob and slide the Seat Carriage (11) to the desired position. Release the seat knob and slide the Seat Carriage back and forth slightly until it locks into position. 10. Identify the Right Pedal (37), which is marked with an “R.” Using an adjustable wrench, tighten the Right Pedal clockwiseinto the Right Crank Arm (65). Tighten the Left Pedal counterclockwiseinto the Left Crank Arm (not shown). Adjust the Right Pedal Strap (38) to the desired position, and press the end of the Pedal Strap onto the tab on the Right Pedal (37). Adjust the Left Pedal Strap (not shown) in the same way. 9 11 80 Knob 10 65 38 37 Tab 11. Make sure that all parts are tightened before you use the exercise cycle. Place a mat beneath the exercise cycle to protect the floor. 7 HOW TO OPERATE THE EXERCISE CYCLE HOW TO ADJUST THE POSITION OF THE SEAT For effective exercise, the seat should be in the proper position. As you pedal, there should be a slight bend in your knees when the pedals are in the farthest position. To adjust the seat, pull the seat knob and slide the seat carriage to the desired position. Relea...