Votos - , Puntuación media:
(
)
)
Fabricar: Horizon Fitness
Tamaño del archivo: 1.5 mb
Nombre del archivo: LS_625E_User_Guide_Rev.1.4.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
D) Attach the right FRONT BASE COVER to the right side FRONT STABILIZER TUBE using 2 SCREWS (D). E) Repeat on the left side. BEFORE YOU BEGIN ASSEMBLY ELLIPTICAL INTRODUCTION OPERATION CONDITIONING GUIDELINES TROUBLESHOOTING & MAINTENANCE LIMITED WARRANTY IMPORTANT PRECAUTIONS A) Open HARDWARE BAG FOR STEP 2. B) Carefully pull the CONSOLE CABLES through the CONSOLE MAST using the twist tie located inside the CONSOLE MAST. C) Attach the CONSOLE MAST to the MAIN FRAME using 4 BOLTS (A), 4 SPRING WASHERS (B) and 4 FLAT WASHERS (C). D) Insert the TOP FRONT COVER, followed by the TOP BACK COVER and snap them together. E) Slide CONSOLE MAST BOOT down to seal the console mast hole. ASSEMBLY STEP 2 CONSOLE MAST BOLT (A) SPRING WASHER (B) FLAT WASHER (C) MAIN FRAME CONSOLE MAST BOOT TOP FRONT COVER TOP BACK COVER CONSOLE WIRES ................ .......... ............ .................................. .......... ............ .............................. .......... ............ HARDWARE BAG FOR STEP 2 CONTENTS : 10 INTRODUCTION IMPORTANT PRECAUTIONS ASSEMBLY BEFORE YOU BEGIN ELLIPTICAL OPERATION LIMITED WARRANTY TROUBLESHOOTING & MAINTENANCE CONDITIONING GUIDELINES CONSOLE MAST LOWER HANDLEBAR PRE-ATTACHED BOLT & WASHER UPPER HANDLEBAR PRE-ATTACHED SET SCREWS NOTCH TAB NOTE: There is NO hardware bag for this step. All hardware is pre-installed. A) Remove PRE-ATTACHED BOLT & WASHERS from CONSOLE MAST. B) Slide LOWER HANDLEBARS onto CONSOLE MAST and attach by re-inserting PRE-ATTACHED BOLT & WASHERS. C) Slide UPPER HANDLEBARS onto LOWER HANDLEBARS and align NOTCH with TAB making sure handlebars are joined together completely. Secure UPPER HANDLEBARS to LOWER HANDLEBARS using PRE-ATTACHED SET SCREWS. D) Snap the front and back HANDLEBAR COVERS together onto the UPPER HANDLE BARS. Note the position of the snap tabs on the covers before snapping into position. E) Repeat on other side. After handlebars are assembled they will rotate freely – be cautious. Until the machine is fully assembled, do not grab the handlebars for support. ASSEMBLY STEP 3 FRONT HANDLEBAR COVER BACK HANDLEBAR COVER UPPER HANDLEBAR LOWER HANDLEBAR BEFORE YOU BEGIN ASSEMBLY 11 ELLIPTICAL INTRODUCTION OPERATION CONDITIONING GUIDELINES TROUBLESHOOTING & MAINTENANCE LIMITED WARRANTY IMPORTANT PRECAUTIONS ASSEMBLY STEP 4 PEDAL ARMS LOWER LINK ARM SPACER (F) BOLT (G) FLAT WASHER (C) SPLIT TEFLON WASHER (E) FOOTPLATE TUBE TEFLON WASHER (E) U BRACKET BOLT (G) FLAT WASHER (C) FOOTPLATE TUBE SPACER (F) SPLIT TEFLON WASHER (E) U BRACKET TOP VIEW OF LEFT FOOT PAD INSERT SPACER THIS DIRECTION A ) Open HARDWARE BAG FOR STEP 4. B) Align LOWER LINK ARM with U BRACKET. CAUTION: Be careful to keep the LOWER LINK ARM aligned with guide rail. Do not twist it to the left or right while positioning it on the U BRACKET. C) Slide SPACER (F) through U BRACKET and FOOTPLATE TUBE. D) Insert FLAT WASHER (C) and BOLT (G) into outside end of FOOTPLATE TUBE E) Insert 2 SPLIT TEFLON WASHERS (E) on left and right sides of FOOT PLATE TUBE & Tighten Bolt (G). F) Repeat on other side. BOLT (G) 15 mm Qty: 2 SPACER (F) 70 mm axis Qty: 2 FLAT WASHER (C) 35 mm Qty: 2 SPLIT TEFLON WASHER (E) 24 mm Qty: 4 HARDWARE BAG FOR STEP 4 CONTENTS : 12 INTRODUCTION IMPORTANT PRECAUTIONS ASSEMBLY BEFORE YOU BEGIN ELLIPTICAL OPERATION LIMITED WARRANTY TROUBLESHOOTING & MAINTENANCE CONDITIONING GUIDELINES ASSEMBLY STEP 5 A) Open HARDWARE BAG FOR STEP 5. B) Slide SPACER (I) into LOWER HANDLEBAR. C) Place TEFLON WASHERS (E) on either side of SPACER (I). While holding TEFLON WASHERS (E) slide LOWER LINK ARM into bottom end of LOWER HANDLEBAR. D) Insert BOLT (H) into LOWER HANDLEBAR and secure using NUT (J). E) Attach the OUTSIDE ELBOW COVER to elbow joint using 1 SCREW (F). F) Snap the INSIDE ELBOW COVER onto the OUTSIDE ELBOW COVER. Note the position of the snap tabs before snapping into position. G) Repeat on other side. START / STOP MODE P1 MANUAL P5 RAMP P3 VALLEYP4 FAT BURN P7 RANDOMP8 TARGETHR PROGRAMS ENTER LOWER HANDLEBAR LOWER LINK ARM INSIDE ELBOW COVER OUTSIDE ELBOW COVER SCREW (F) GUIDE RAIL TEFLON WASHERS (E) LOWER HANDLEBAR NUT (J) BOLT (H) LOWER LINK ARM SPACER (I) LOWER LINK ARM SPACER TEFLON WASHERS LOWER HANDLEBAR BEFORE YOU BEGIN ASSEMBLY 13 ELLIPTICAL INTRODUCTION OPERATION CONDITIONING GUIDELINES TROUBLESHOOTING & MAINTENANCE LIMITED WARRANTY IMPORTANT PRECAUTIONS ASSEMBLY STEP 6 NOTE: There is NO hardware bag for this step. All hardware is pre-installed. A) Attach the CONSOLE MAST wires to the CONSOLE wires . B) Carefully tuck the CONSOLE MAST wires into the CONSOLE MAST before attaching the CONSOLE. C) Attach CONSOLE to the CONSOLE MAST using the 4 PRE-ATTACHED SCREWS (screws will have to be removed from the console first). DO NOT PINCH WIRES! YOU’RE FINISHED! NUT (J) INSIDE DIAMETER: 8 mm Qty: 2 BOLT (H) 60 mm Qty: 2 SPACER (I) 44 mm Qty: 2 TEFLON WASHER (E) 24 mm Qty: 4 SCREW (F) Qty: 2 HARDWARE BAG FOR STEP 5 CONTENTS : START / STOP MODE PROGRAMS ENTER CONSOLE CONSOLE MAST CONSOL...