Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Insert bolt (A) and FLAT WASHER (B) into left linkage arm followed by a teflon washer (C) and attach to elevation frame. D Lift left console mast into upright position. Be sure to hold the console mast firmly, as it will not stay in the upright position on its own. E Insert bolt (D) and 1 FLAT washer (E) through left console mast followed by a WAVY washer (F) and attach to MAIN FRAME. DO NOT ATTEMPT TO LIFT THE TREADMILL!* Do not move or lift treadmill from packaging until specified to do so in the assembly instructions. Failure to do so may result in injury! Remove plastic wrap from console masts. Note: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt. NOTE: A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike grease is recommended. WARNING IMPORTANT INTRODUCTION ASSEMBLY PRECAUTIONS BEFORE YOU BEGIN TREADMILL OPERATION CONDITIONING GUIDELINES TROUBLESHOOTING & MAINTENANCE LIMITED WARRANTY ASSEMBLY STEP 2 ELEVATION FRAME BOLT (D) RIGHT LINKAGE ARM FLAT WASHER (E) MAIN FRAME RIGHT CONSOLE MAST CONSOLE CABLES PRE-ATTACHED BOLT WAVY WASHER (F) FOOT LOCK LATCH ................ .......... ............ ................ .................... .............................. ............ ............................ ............ HARDWARE BAG 2 CONTENTS : RIGHT CONSOLE MAST LEAD WIRE CONSOLE CABLES Pull LEAD WIRE through RIGHT CONSOLE MAST. After pulling the lead wire through the mast, the top of the console cables should be located at the top of the mast. Detach and discard lead wire. Open HARDWARE BAG 2. Move right linkage arm into position and attach to ELEVATION FRAME. Note: While holding RIGHT CONSOLE MAST in the upright position, tighten PRE-ATTACHED BOLT using T-wrench to attach RIGHT LINKAGE ARM. Attach RIGHT CONSOLE MAST to MAIN FRAME using 1 BOLT (D), 1 FLAT WASHER (E) and 1 WAVY WASHER (F). Lift the running deck until lock latch on side of treadmill is fully engaged. Remove console from box and place out of the way. Lower the treadmill running deck from the folded position by stepping on LOCK LATCH on lower right side. A. B. C. D. E. F. G. 1 3 2 Note: If you have attempted to move the treadmill from the box and the machine has sprung open and cannot be assembled, refer to the troubleshooting section in order to restore the treadmill to its proper position. * 10 INTRODUCTION IMPORTANT PRECAUTIONS ASSEMBLY BEFORE YOU BEGIN TREADMILL OPERATION LIMITED WARRANTY TROUBLESHOOTING & MAINTENANCE CONDITIONING GUIDELINES ASSEMBLY STEP 3 Step4 FLAT WASHER (B) CONSOLE MAST CONSOLE CABLES SPRING WASHER (H) BOLT (G) CONSOLE DO NOT ATTACH THIS SIDE UNTIL STEP 3-D FLAT WASHER (B) 20 mm Qty: 4 SPRING WASHER (H) 15 mm Qty: 4 BOLT (G) 20 mm Qty: 4 HARDWARE BAG 3 CONTENTS : A Open HARDWARE BAG 3. B With running deck in lowered position, place console on the console masts. Align the brackets that are underneath the console with the top holes of the console masts. C To assemble the CONSOLE to the left CONSOLE MAST, insert 1 BOLT (G), 1 SPRING WASHER (H) and 1 FLAT WASHER (B) into the 2 holes in the left CONSOLE mast and lightly tighten. D Gently lift right side of the console to connect the console cable. Carefully tuck wire in mast to avoid damage. NOTE: Do not pinch console cable or grip pulse wires. E Repeat step C above to assemble the right console mast to the console. F Leave console bolts loose until after STEP 4 is completed. A S S E M B LY S T E P HARDWARE BAG CONTENTS : BOLT (I) 15 mm Qty: 4 BOLT (I) CONSOLE MAST SUPPORT BAR Open HARDWARE BAG .A. B. Align SUPPORT BAR with holes in CONSOLE MASTS. C. Insert BOLTS (I) into all 4 holes of the SUPPORT BAR. NOTE: Look into holes in the right mast before inserting bolts to avoid pinching cables. D. Tighten all console bolts (Step 3) and support bar bolts (Step 4) completely. LIMITEDTROUBLESHOOTINGCONDITIONINGTREADMILLBEFORE ASSEMBLY IMPORTANT INTRODUCTION WARRANTY & MAINTENANCE GUIDELINES OPERATION YOU BEGIN PRECAUTIONS 11 12 INTRODUCTION IMPORTANT PRECAUTIONS ASSEMBLY BEFORE YOU BEGIN TREADMILL OPERATION LIMITED WARRANTY TROUBLESHOOTING & MAINTENANCE CONDITIONING GUIDELINES ASSEMBLY STEP 5 CONSOLE MAST CONSOLE SET SCREWS (J) HANDLEBAR BOLT (K) ARC WASHER (L) SET SCREW (J) 12 mm Qty: 4 BOLT (K) 120 mm Qty: 2 ARC WASHER (L) 17 mm Qty: 2 angle view HARDWARE BAG 5 CONTENTS : A Open HARDWARE BAG 5. B Slide LEFT HANDLEBAR to CONSOLE and attach using 2 SET SCREWS (J). C Attach LEFT HANDLEBAR to CONSOLE MAST using 1 BOLT (K) and 1 ARC WASHER (L). D Repeat on other side. NOTE: Look into holes in the right mast before inserting bolts to avoid pinching cables. YOU’RE FINISHED! POWER SWITCH CIRCUIT BREAKER Connect power plug to the treadmill and connect the cord to a power outlet. The on/off switch is located next to the power cord. Flip this switch to the 'ON' position, so that the switch is lit. You will hear a beep and the console will turn on. C...