Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
It is the responsibility of the owner to ensure that all users of this indoor cycle are adequately informed of all warnings and precautions. If you have any questions after reading this owner’s manual, contact Customer Tech Support at the number listed on the back panel. wARNINg READ AND SAVE ALL INSTRUCTIONS bEfORE ASSEmbLINg OR USINg THIS INDOOR CyCLE. IT IS STRONgLy RECOmmENDED TO TAkE THE fOLLOwINg SAfETy INSTRUCTIONS. • CAUTION: If you experience chest pains, nausea, dizziness or shortness of breath, stop exercising immediately and consult your physician before continuing. • Use this cycle for its intended purpose as described in this manual. Do not use attachments that have not been recommended by the manufacturer. • Never operate the cycle if it is not working properly, or if it has been damaged. Contact Horizon Fitness or the authorized dealers for examination and repair. • Do not use the cycle without proper footwear. NEVER operate the cycle with bare feet. • Do not wear any clothing that might catch on any moving parts of this cycle. • Keep hands and feet clear at all times from moving parts to avoid injury. Never turn the pedal cranks by hand. • Do not dismount the cycle until the pedals are at a complete STOP. • Do not attempt to ride the cycle in a standing position at high RPMs until you have practiced at slower speeds. • Do not insert any object, hands or feet into any openings, or expose hands, arms or feet to the drive mechanism or other potentially moving part of the cycle. • Do not use any equipment that is damaged or has worn or broken parts. Use only replacement parts supplied by Horizon Fitness or the authorized dealers. • Do not operate where aerosol (spray) products are being used or when oxygen is being administered. • Close supervision is necessary when used near children, invalids or disabled people. • When the cycle is in use, young children and pets should be kept at least 3 meters / 10 feet away. • After exercising, push down on the tension knob or turn the tension knob in a clockwise direction to slow the flywheel down and decrease the potential for injury. • Ensure that adjustment levelers (seat and handlebar height, seat and handlebar fore-and-aft) are properly secured and do not interfere with range of motion during exercise. 5 ASSEMBLY There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the indoor cycle could have parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the indoor cycle, the assembly instructions must be reviewed and corrective actions should be taken. Before proceeding, find your indoor cycle’s serial number located on the lower front of the cycle and enter it in the space provided below. ENTER YOUR SERIAL NUMBER IN THE BOX BELOW: » Refer to the SERIAL NUMBER and MODEL NAME when calling for service. » Be sure to enter both the SERIAL NUMBER and MODEL NAME on your warranty card. SERIAL NUMBER: MODEL NAME: Hori zon P8000 INDOOR CYCLE WARNING SERIAL # PLACEMENT 6 TOOLS/FASTENERS INCLUDED: FF Socket Head Screw FF 5 mm Allen Wrench FF Open Wrench (#13 / #14 / #15) PARTS INCLUDED: A) Main Frame Assembly B) Handlebar Set C) Seat D) Rear Foot E) Front Foot F) Pedals G) Quick Release Lever Set H) Hardware Kit If you have questions or if there are any missing parts, contact Customer Tech Support. Contact information is located on the back panel of this manual. NEED HELP? (A) (B) (C) (D) (F) (G) (H) (E) P8000 PARTS INCLUDED 7 This unit weighs 118 lbs / 54 kg. To avoid injury to the user and the unit, be sure to have proper assistance to remove or move the unit. CAUTION UNPACKING The P8000 Indoor Cycle is carefully inspected before it is packaged. Remove all parts from the shipping carton and foam inserts, and verify that the following parts are included in your shipment. After unpacking, dispose of the carton material properly. NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt. NOTE: A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike grease is recommended. PRE ASSEMBLY Z01 Z01 Z01 AT2 Z01 D06 AG2 G11 G10 D14 G10 ASSEMBLY EXPLODED DIAGRAM ASSEMBLY STEP 1 Z01Z01Z01Z01 A Place the front foot in position at the front of the cycle, with the transport wheels facing forward, aligning the two holes in the foot with the mating holes in the frame bracket. B Insert the two screws (Z01) through the frame bracket and front foot. Using the #5 Allen Wrench (Z31) to tighten the screws securely. C Place the rear foot in position at the rear of the cycle, aligning the two holes in the foot with the mating holes in the frame bracket. D Insert the two screws (Z01) through the frame bracket...