Votos - 5, Puntuación media: 3.4
(
)
)
|
Resumen del manual
SAFETY PRECAUTIONS • This Power System unit should only be used on a level surface and is intended for indoor use only. Keys Fitness recommends an equipment mat be placed under the unit to protect the floor or carpet and for easier cleaning. • Wear comfortable, good-quality walking or running shoes and appropriate clothing. Do not use this unit with bare feet, sandals, socks or stockings! • Always examine your unit before using to ensure all parts are in working order. • Do not leave children unsupervised near or on the unit. • Service to your Power System unit should only be performed by an authorized service representative, unless authorized and/or instructed by a Keys Fitness technician. Failure to follow these instructions will void the warranty. 4 Assembly 5 Assembly 6 Step 1 Slide one Pillow Block Bearing (17) onto each side of the Back Rocker (5). Use two Bolts (33), four Washers (44), and two Nylon Locknuts (41) to attach each Pillow Block Bearings (17) onto the Main Frame (1). Slide Short Spacer Tube (12) into the Front Rocker (4). Attach the Front Rocker (4) to the Main Frame (1) using one Bolt (34), two Washers (44), and one Nylon Locknut (41). Insert Long Spacer Tubes (11) into the top of Front and Back Rocker (4 & 5). Attach the Connect Frame (6) to the top of the Front and Back Rocker (4 & 5). Next, insert two Bushings (29) into each side of the Connect Frame (6). Next, slide both Long Shafts (13) into Connect Frame (6) and secure in place by using four Washers (44) and four Nylon Lock-nuts (41). Assembly 7 Figure 1 Assembly 8 Step 2 Attach Foot Plate (7) to the Connect Frame (6) using three Bolts (32), three Washers (44), and three Nylon Lock-nuts (41). Attach Right Handle (2) and Left Handle (3) to the Main Frame (1) using two Bolts (39), four Washers (43), and two Nylon Lock-nuts (42). Figure 2 Assembly 9 Step 3 Attach Cross Base (8) to Main Frame (1) using Plate (14), two Bolts (39), four Washers (43), and two Nylon Lock-nuts (42). Slide Pulley Block (10) onto the Cross Base (8) and secure in place using two Bolts (40), four Washers (43), and two Nylon Lock-nuts (42). Figure 3 Assembly 10 Figure 4 Step 4 Attach Seat Pad (24) to Main Frame (1) using two Bolts (38) and two Washers (43). Assemble Back Pad (23) to Back Pad Support (9) using two Bolts (35) and two Washers (43). Slide Back Pad Support assembly to Main Frame (1) and secure using Pop Pin (16). Assembly 11 Step 5 Start by attaching Cable (15) to Main Frame (1). See detail A below. Insert cable into Pulley A location and then attach Pulley A to Main Frame (1) using one Bolt (36), two Washers (43), and one Nylon Locknut (42). Note: Make sure cable is running through the groove of each pulley. Note: All pulleys use the same hardware to attach to Main Frame (1). Attach Pulley B to Main Frame (1) and then run cable over top of the pulley. Run cable though slot in Main Frame (1) at Pulley C location. Insert Pulley C into Main Frame (1), insure cable runs through bottom side of pulley. Run cable through Pulley D location and then install Pulley D onto Main Frame (1). Run cable through Pulley E location and then install Pulley E onto Main Frame (1). Last, thread cable end into the floating pulley of home gym unit. Figure 5 Congratulations! You have completed the assembly of your new KPS-LP2. Note: Tighten all hardware securely. Weight Ratios 12 KPS-LP2 Ratio % Weight(lbs) 205% 10 20.5 15 30.75 20 41 25 51.25 30 61.5 35 71.75 45 92.25 55 112.75 65 133.25 75 153.75 85 174.25 95 194.75 105 215.25 115 235.75 125 256.25 140 287 155 317.75 170 348.5 185 379.25 200 410 Exploded View 13 Parts List KPS-LP2 Parts List REF# KEYS PART# DESCRIPTION QTY. 1 223-00249 Main Frame 1 2 219-00280 Right Handle 1 3 219-00285 Left Handle 1 4 223-00250 Front Rocker 1 223-00251 Back Rocker 1 6 219-00282 Connect Frame 1 7 223-00252 Footplate 1 8 223-00253 Cross Base 1 9 219-00283 Back Pad Support 1 219-00284 Pulley Block 1 11 210-00062 Long Spacer Tube 2 12 210-00063 Short Spacer Tube 1 13 230-00020 Long Shaft 2 14 210-00064 Plate 1 229-00052 Cable 1 16 210-00068 Pop Pin 1 17 210-00069 Pillow Block Bearing 2 18 206-00139 Square Plug 50*25 6 19 206-00001 Square Plug 76.2*50.8 2 206-00020 Square Plug 44.5 1 21 206-00140 Square Plug 50.8 1 22 206-00102 Round Plug 32 2 23 228-00086 Back Pad 1 24 228-00087 Seat Pad 1 223-00228 4.5"Pulley 5 26 206-00144 Base Cushion 2 27 202-00023 Bronze Bushing 6 28 202-00025 Pulley Spacer 2 29 202-00148 Iron Bushing 4 206-00145 Foam 2 31 206-00149 Rubber Cushion 1 32 202-00150 Bolt M12x55 3 33 202-00151 Bolt M12x40 4 34 202-00152 Bolt M12x105 1 202-00124 Bolt M10x30 2 36 202-00085 Bolt M10x50 4 37 202-00083 Bolt M10x70 1 38 202-00081 Bolt M10x75 4 39 202-00082 Bolt M10x80 4 202-00080 Bolt M10x85 2 41 202-00092 Nylon Locknut M12 12 42 202-00091 Nylon Locknut M10 13 43 202-00128 Washer 11*20*2 30 44 202-00127 Washer 13*24*1.5 17 202-00153 Allen Wrench S=3 1 14 Warranty Information KEYS FITNESS PRODUCTS, L.P. POWER SYSTEM SERIES LIFETIME ...