Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Tighten all Nylon Locknuts (11) used in steps 1–13. 56 58 5 53 15 15 13 Ball 11 58 14 57 10 41 10 11 11 53 9 6 56 Bracket 2 14. Identify the High Cable (13), which is the shorter of the two Cables. Route the High Cable up through the indicated slot in the Pulley Bar (53). Make sure the ball is in the indicated location. Route the High Cable (13) around a Pulley (5) as shown. Attach the Pulley inside the slot in the Pulley Bar (53) using an M10 x 65mm Bolt (56), two M10 Large Washers (58), two Pulley Spacers (15), and an M10 Nylon Locknut (11). Do not overtighten the Nylon Locknut; the Pulley must be able to turn freely. 13 10 15. Route the High Cable (13) around another Pulley (5) and through the indicated slot in the Pulley Bar (53) as shown. Attach the Pulley inside the slot using an M10 x 65mm Bolt (56), two M10 Large Washers (58), two Pulley Spacers (15), and an M10 Nylon Locknut (11). Do not overtighten the Nylon Locknut; the Pulley must be able to turn freely. 16. Route the High Cable (13) up through the Pulley Bar (53), around another Pulley (5), and back through the Pulley Bar, as shown. Attach the Pulley inside the slot in the Pulley Bar using an M10 x 65mm Bolt (56), two M10 Large Washers (58), two Pulley Spacers (15), and an M10 Nylon Locknut (11). Do not overtighten the Nylon Locknut; the Pulley must be able to turn freely. 56 58 53 58 11 13 5 15 15 15 16 5 15 56 58 15 11 13 58 53 17. Attach the end of the High Cable (13) to the M10 x 20mm Bolt (26) in the Weight Carriage (22) with an M10 Nylon Locknut (11). 18. Hold a Pulley (5) inside the High Cable (13) as shown. Attach the Pulley and a Cable Trap (21) to the indicated set of holes in the two Pulley Plates (19) with an M10 x 45mm Bolt (40) and an M10 Nylon Locknut (11). Make sure the Cable Trap holds the High Cable in the groove of the Pulley. Do not overtighten the Nylon Locknut; the Pulley must be able to turn freely. 5 21 40 11 19 13 18 11 22 26 13 17 11 19. Wrap the ball end of the Low Cable (8) around a Pulley (5). Attach the Pulley to the bracket on the Base Crossbar (20) with an M10 x 45mm Bolt (40) and an M10 Nylon Locknut (11). Do not overtighten the Nylon Locknut; the Pulley must be able to turn freely. Be sure the ball is on the indicated side of the bracket. 20. Route the Low Cable (8) around a Pulley (5) as shown. Attach the Pulley and a Cable Trap (21) to the lowest set of holes in the two Pulley Plates (19) using an M10 x 45mm Bolt (40) and an M10 Nylon Locknut (11). Make sure the Cable Trap holds the Low Cable in the groove of the Pulley. Do not overtighten the Nylon Locknut; the Pulley must be able to turn freely. 20 40 8 11 Ball Bracket 5 20 19 40 21 8 5 11 19 21. Attach the end of the Low Cable (8) to the bracket on the Rear Base (3) using an M10 x 20mm Bolt (26) and an M10 Nylon Locknut (11). 21 26 11 3 8 Bracket 22. Press a 50mm x 70mm Outer Cap (65) onto each end of the Stabilizer (66). Attach the Stabilizer (66) to the Bench Frame (61) with two M10 x 60mm Button Head Bolts (92) and two M10 Nylon Locknuts (11). Note: Do not tighten the Nylon Locknuts yet. There is an indentation around each hole on one side of the Stabilizer; this side must be facing the floor. 22 92 65 11 61 66 65 12 23. Press a 50mm Square Outer Cap (73) onto each end of the Bench Base (62). Attach the Bench Base Joint Plate (72) to the Bench Base (62) with two M10 x 70mm Bolts (91), two M10 Large Washers (58), and two M10 Nylon Locknuts (11). Attach the Bench Leg (59) to the Bench Base Joint Plate (72) with two M10 x 70mm Bolts (91), two M10 Large Washers (58), and two M10 Nylon Locknuts (11). Be sure the welded nut is in the position shown. Do not tighten the M10 Nylon Locknuts (11) yet. 23 91 58 58 91 58 58 59 11 72 73 73 62 Welded Nut 24. Attach the Bench Leg (59) to the Bench Frame (61) with two Thick Joint Plates (71), four M10 x 70mm Bolts (91), and four M10 Nylon Locknuts (11). Note: Tighten all the M10 Nylon Locknuts (11) used in steps 22–24. 24 59 11 71 61 91 71 25. Press two 25mm x 40mm Inner Caps (79) into each Backrest Tube (78). Press two 25mm x 40mm Inner Caps into the Backrest Adjustment Bracket (83). Lubricate an M10 x 190mm Bolt (75). Attach the Backrest Tubes (78) to the welded tube on the Backrest Adjustment Bracket (83) with the Bolt, two M10 Large Washers (58), and an M10 Nylon Locknut (11). Make sure that the Backrest Tubes are turned as shown. The indicated holes are not centered in the Backrest Tubes. Turn the Backrest Tubes so the holes are closer to the floor. Do not overtighten the Nylon Locknut; the Backrest Tubes must pivot easily. 25 79 11 83 Lubricate Holes Welded Tube 79 79 75 58 58 78 26. Lubricate an M10 x 190mm Bolt (75). Attach the Backrest Tubes (78) to the welded tube on the Bench Frame (61) with the Bolt, two M10 Large Washers (58), and an M10 Nylon Locknut (11). Note: Do not overtighten the Nylon Locknut; the Backrest Tubes must pivot easily. 26 78 11 61 75 58 58 Lubricate Welded Tube 13 29. Place the Seat Mount...