Votos - 1, Puntuación media: 3 ( )

Fabricar: Invacare Tamaño del archivo: 606.46 kb Nombre del archivo: Idioma del manual:

Position the mounting bracket on the mattress deck (FIGURE 7). 5. Secure the mounting bracket to the mattress deck with the two hex bolts and locknuts (FIGURE 7). 6. Install the positioning device into the mounting bracket by sliding the mounting pin of the bed rail through the pivot tube (FIGURE 7). 7. Secure positioning device in place with two retaining clips (FIGURE 7). NOTE: Ensure that the release lever is pointing towards the foot end of the bed. 8. Slide the nylon washer over the end of the mounting pins (FIGURE 7). 9. Snap retaining clips into grooves on the end of the mounting pins (FIGURE 7). 10. Head End Mounting Bracket Only - Position the crossmember between the two bed rails (FIGURE 7). NOTE: Repeat STEPS 3-9 to install the other positioning device on the opposite side. Part No 1143214 5 ICCI Bed Rails and Accessories ICCI Bed Rails and Accessories 6 Part No 1143214 FIGURE 7 Installing the IHRAILTS-DLX Positioning Device Using the IHRAILTS-DLX Positioning Device NOTE: For this procedure, refer to FIGURE 8. 1. Perform one of the following: • Raising - Pull up on the positioning device while rotating towards the head end of the bed until the positioning device locks into place. • Lowering - Pull up on the release lever and push down on the positioning device while rotating towards the foot end of the bed until the positioning device lowers into place. FIGURE 8 Using the IHRAILTS-DLX Positioning Device Changing the Head Board Mounting Position NOTE: For this procedure, refer to FIGURE 9. NOTE: When using bed rails 6815A, 6816A, 6803A or IHRAILTS - DLX in conjunction with an 80-inch mattress, the head board mounting brackets MUST be adjusted. 1. Remove the two mounting screws that secure head board mounting bracket to the bed frame. See Detail “A”. 2. Secure the head board mounting bracket to the bed frame as shown in Detail “B” using two mounting screws and locknuts. Securely tighten. NOTE: Ensure mounting brackets are perpendicular to the floor. 3. Repeat STEPS 1-2 to install remaining head board mounting brackets. Release Lever (Towards the foot end of the bed) Mounting Bracket Hex Bolt Locknut Attach Head End Crossmember Here Mattress Deck Pivot Tube IHRAILTS-DLX Positioning Device Washer Retaining Clip Mounting Pin IHRAILTS-DLX Positioning Device Mattress Deck Mounting Bracket Pivot Tube Washer Retaining Clip Crossmember Positioning Device Release Lever DETAIL “B” DETAIL “A” NOTE: Mounting position of head board mounting bracket for bracket for use with 80-inch mattress - without side NOTE: Mounting position of head board mounting use with 80-inch mattress - using side rails 6815A, 6816A, rails 6803A, or IHRAILTS-DLX. Bed Frame Mounting Screws and Locknuts Head Board Mounting Bracket 2-inch Gap Head Board Mounting Bracket Mounting Screws and Locknuts Bed Frame 1-inch Gap FIGURE 9 Changing the Head Board Mounting Position Changing the Mounting Position of the Mattress Keepers NOTE: For this procedure, refer to FIGURE 10 on page 7. NOTE: When using bed rails 6815A, 6816A, 6803A or IHRAILTS_DLX in conjunction with an 80-inch mattress, the mattress keepers on the head end of the mattress deck MUST be adjusted. 1. Remove the two mounting screws that secure the mattress keeper to the head end of the mattress deck. See Detail “A”. 2. Secure the mattress keeper to the head end of the mattress deck as shown in Detail “B” using two mounting screws and locknuts. Securely tighten. 3. Repeat STEPS 1-2 to adjust the remaining mattress keeper on the head end of the mattress deck. Mattress Keeper Mounting Screws and Locknuts DETAIL “A” NOTE: Mounting position of the mattress keeper fo...

Descargar ahora

Introduzca dos números de la imagen: