Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
- 8325 p/n 108325 Specifications . Height: 75”(24”packed) . W idth: 72” . Depth: 92”(40”packed) . Weight: 135 lbs. .Instruction p/n 102479 -C l a m C ust o m e r S er vi ce I nf o r m at i o n - NOTICE!! Once used, this shelter cannot be returned to the store. If you have a warranty claim, have your sales receipt ready and contact Clam Corporation Customer Service by email inquiry or direct by calling: . Customer Service Hrs: -9am to 4pm, Mon. . Clam Corporation 600 Clydesdale Trail Medina, MN 55340 . Phone -763-231-4120 . Fax -763-231-4121 . Website – . Email – customerservice@clamcorp.com Fri. Central Standard Time Clam Corporation cannot honor warranty without an original, dated receipt. -P art s Li st --P art s Li st - ITEM NO. PART NUMBER DESCRIPTION QTY. 102498 BASE, VOYAGER, 08/09 1 101479 TUBE, PORCH HOOP 1 101585 BRKT, RIGHT CANOPY 1 101463 FOLDING SEAT ASSEMBLY 2 101482 TUBE, CANOPY HOOP 3 101130 LONG ROOF SPREADER 1 101124 SHORT ROOF SPREADER POLE 1 101458 CONSOLE, CLAM CENTER 1 101580 REAR SPREADER POLE 1 101069 POLE CANOPY, 1/2" 6 102504 TUBE, RAIL SUPPORT 08/09 1 101083 CAP, TUBE SPACER 8 101080 SCREW, 1/4-20 X 1.25 8 101081 WASHER, 1/4 FLAT REG 8 101082 NUT, 1/4-20 THIN NYLOCK 32 101584 BRKT, LEFT CANOPY 1 101088 SCREW, 1/4-20 X 0.75 6 101487 SCREW, 1/4-20 X 2.75 2 101430 CAP, TUBE 1 X 2 - 1/8 WALL 2 101116 MOLDING, 3/4 X 118 U-CHNL 1 101095 ROPE, 3/8 DIA X 9 FT 1 101148 SCREW, #6 X 0.38 16 102430 BRKT, REAR RETAINER 2 102512 SPRING, CATCH 2 101048 BLOCK, SLIDE 8 101652 TUBE, 20.00 SEAT RAIL 4 101466 HAMMOCK, ACCESSORY 2 101429 PLUG, 1.16 DIA TUBE 8 101420 BRKT, FRONT RETAINER 2 101486 SCREW, 1/4-20 X 1.75 8 101146 CHANNEL, 8.78 ALUM EXT 4 101167 FRONT SPREADER POLES 2 101399 SEAT SWIVEL 2 101147 SCREW, #10 x 1.00 8 101470 SCREW, 1/4-20 X 0.50 16 101121 TUBE, PORCH 2 102436 TENT, 08/09 VOYAGER 1 102479 MANUAL, 08/09 VOYAGER 1 2 -As s e m bl y Di a g r a m --As s e m bl y Di a g r a m - 3 -St e p O n e --St e p O n e - 4 -St e p Tw o --St e p Tw o - 5 -St e p T hr e e --St e p T hr e e - 6 -St ep F o u r --St ep F o u r - 7 -St ep Fi v e --St ep Fi v e - Rear Seat Bracket (p/n 102430) Latch Clip (p/n 102512) 8 -St e p Si x --St e p Si x - Voyager Base (p/n 102498) 1”x2 ”Rectangular Support Tube (p/n 102504) 9 -St e p S e ve n - Slide the canopy hoop poles onto the canopy poles until the spring buttons engage the holes near the ends of each canopy hoop pole. Support the first canopy hoop pole as pictured with the rear adjustable spreader poles (the shorter of the two provided lengths). Lean the two remaining canopy hoop poles against the first. Canopy Hoop Pole (p/n 101482) -St e p S e ve n - Slide the canopy hoop poles onto the canopy poles until the spring buttons engage the holes near the ends of each canopy hoop pole. Support the first canopy hoop pole as pictured with the rear adjustable spreader poles (the shorter of the two provided lengths). Lean the two remaining canopy hoop poles against the first. Canopy Hoop Pole (p/n 101482) 10 -St e p Ei ght --St e p Ei ght - Drape the tent over the supported hoops then go inside and spread out the canopy hoop poles, attaching the roof velcro as you go. Orient the porch hoop pole so that the holes face upward and then feed the length of the pole through the three porch hoop sleeves sewn on the tent. Slide the porch hoop pole onto the porch poles, engaging the third hole position. Attach the porch hoop velcro on each side of the tent. Remove the rear adjustable spreader poles now supporting the hoops to allow the tent to be “set” in the next step. Porch Hoop Pole (p/n 101479) Voyager Tent (p/n 102436) 11 -St ep N i n e - To “set”the tent, grasp the tent material at the rear of the shelter and pull it downward. Observe the porch area of the tent lifting accordingly as you pull. When the U-Channel molding is correctly installed, the porch hoop pole will lightly touch the floor. To achieve this condition, start by finding the center of the molding. From behind the unit, pull the midpoint of the tent downward and fold the tent material under the base lip. Press the midpoint of the molding over the tent material and base lip. Continue pressing outward in both directions until you have secured about twelve inches of molding onto the base. Having temporarily secured the tent to the base, take a walk around the unit. Readjust the molding until you have verified the proper porch hoop pole position and also that the tent sides and corners are properly proportioned. When satisfied, continue applying the molding around the shelter, one direction from center and then the other, pulling the material as you go so that surface is relatively wrinkle-free and snug. Use a side cutters to trim the ends of the molding if they are not equal relative to base. Reinstall the rear adjustable spreader pole to tighten the fit of the tent. If everything still looks good, secure the molding with the #6 phillips screws. Evenly space them about every ten to twelv...