Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
Installing DIMMs
Caution: Failure to al ow the ports to quiesce can
result in data loss. Quiescing can take several
minutes.
Use the following steps to install DIMMs in a cache module in
dual-redundant configurations:
The ECB must be disabled before disconnecting the ECB
cable from the cache module. Failure to disable the ECB
might result in cache module damage.
Note: Before instal ing DIMMs, note the fol owing:
■
New cache modules arrive without DIMMs installed; the DIMMs
are packaged separately. Unpack the DIMMs and instal them
into the cache module as required.
Note: A countdown timer allows a total of 2 minutes to remove the
cache module. After 2 minutes, “this controller” exits FRUTIL and
■
Both cache modules must contain the same memory
resumes operations. If this happens, return to step 3 on page 4 and
configuration for the ACS version. See Figure 3 and Table 1 on
proceed.
page 2 for valid cache module memory configurations.
■
Some HSG80 controller configurations require a 512-MB
cache memory configuration. Make sure the cache memory
configuration meets or exceeds the ACS requirement. See
9. For HP StorageWorks Model 2100 and 2200 enclosures,
“Cache memory configuration” on page 2.
disengage both retaining levers and remove the “other
controller” cache module.
10. For all other supported enclosures:
1. Insert each DIMM (see Figure 5 on page 3) straight into the
appropriate slot of the cache module, ensuring that the
a. Disengage both retaining levers and partially remove
notches in the DIMM align with the tabs in the slot.
the “other controller” cache module—about halfway.
2. Press the DIMM gently into the slot until seated at both
ends.
Caution: You must disable the ECB before disconnecting
the ECB Y-cable from the cache module. Failure to disable
3. Engage the two retaining clips for the DIMM (see Figure 5
the ECB might damage the cache module.
on page 3).
4. Make sure both ends of the DIMM are firmly seated in the
slot and both retaining clips engage the DIMM.
b. Disable the ECB by pressing in the battery disable
switch while removing the ECB Y-cable from the cache
5. Repeat step 1 through step 4 for each DIMM.
module.
6. If not already connected, connect a PC or terminal to the
c. Release the battery disable switch.
operational controller.
d. Disconnect the ECB cable from the “other controller”
The controller connected to the PC or terminal becomes
cache module.
“this controller,” and the controller for the cache module
being installed becomes the “other controller.”
e. Remove the cache module from the enclosure.
7. Start FRUTIL with the following command:
11. Place the cache module on an antistatic bag or a grounded
antistatic mat.
RUN FRUTIL
8. Enter N(o) to the question about replacing the cache
12. Enter N(o) to the question for a replacement cache module.
battery.
FRUTIL exits.
9. Enter 2 for the install a controller or cache module option.
13. Press down on the DIMM retaining clips at both ends of the
10. Enter 3 for the install the “other controller” cache module
DIMM being removed (see Figure 5 on page 3).
option.
11. Enter Y(es) to confirm the intent to install the “other
Note: To facilitate pressing down on the DIMM retaining clips, use
controller” cache module.
the eraser end of a pencil or a small screwdriver.
12. Wait for FRUTIL to quiesce the device ports—indicated by
an “All device ports quiesced” message.
14. Gently remove the DIMM from the DIMM slot, and then
place it in an antistatic bag or on a grounded antistatic mat.
Caution: Failure to allow the ports to quiesce can result in
15. Repeat step 13 and step 14 for each DIMM being replaced.
data loss. Quiescing can take several minutes.
You must disable the ECB before connecting the ECB cable
to the cache module. Failure to disable the ECB might
damage the cache module.
Careful y align the cache module in the appropriate guide
rails. Misalignment might damage the backplane.
Note: A countdown timer allows a total of 2 minutes to install the
cache module. After 2 minutes, “this control er” exits FRUTIL and
resumes operations. If this happens, return to step 7 and proceed.
Page 5
...Otros modelos de este manual:
datos de dispositivos de procesamiento - HP StorageWorks EMA12000 Blue Bundle (50 Hz) (257.67 kb)
datos de dispositivos de procesamiento - HP StorageWorks EMA12000 Blue Bundle (60 Hz) (257.67 kb)
datos de dispositivos de procesamiento - HP StorageWorks EMA12000 D14 (60 Hz) (257.67 kb)
datos de dispositivos de procesamiento - HP StorageWorks EMA12000 D14 Bundle (50 Hz) (257.67 kb)