Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
Updating Firmware
ESL9000
16
hp
Interface
After replacing the CompactFlash card, you must update the Interface Manager firmware and reconfigure the
Manager
StorageWorks
Interface Manager settings. To update the firmware:
CompactFlash
1. Acquire the latest firmware file from:
4. Start a Telnet session on the PC or laptop that is
Replacement
http://www.hp.com/support/cvtl
connected to the Interface Manager card via the
2. If necessary, transfer the firmware file to a client PC
cascade port:
or laptop that will be used in step 3 to connect to
a. From a command prompt, enter the following:
the Interface Manager card.
telnet 192.168.2.1
b. At the login prompt, enter the following
Caution: The expansion cage and the
Caution: Parts can be damaged by
3. Use ftp to transfer the firmware file to a temporary
information:
expansion cards that it contains are not
electrostatic discharge. Keep parts in their
storage area in the Interface Manager card’s
— Username: cliadmin
hot-pluggable. To avoid damage to
containers until needed. Make sure that you are
memory.
— Password: clipwd
equipment and possible loss of data,
properly grounded when touching static-sensitive
a. Connect a host PC or laptop to the Cascade port
make sure that the library is properly
components.
of the Interface Manager card using an Ethernet
5. Enter the following command to update the
powered down, as described in Step 1,
cable.
firmware:
before proceeding.
b. On the host PC or laptop, open a command shell
download mgmt
and navigate to the directory that the firmware
6. Set the Interface Manager card IP address to the
you downloaded in step 1 is located.
same address it had before replacing the
c. Enter the following command: ftp
CompactFlash card. To set the IP address enter the
192.168.2.1
following command:
This document explains how to replace the
d. Login with the following credentials:
set network ipaddress
1
CompactFlash memory card on the Interface
— User name: ftp
Manager card that is installed in an HP
— Password: Use your e-mail address
Power off the
7. Logoff the telnet connection and disconnect the host
StorageWorks ESL9000-Series tape library.
ESL9000 Series
e. If necessary, use the ls command to list the
contents of the ftp directory.
PC or laptop from the Cascade port of the Interface
Caution: This procedure will cause all
library.
f
Manager card.
. Enter the following command to turn on binary
Interface Manager card configuration
a. Press Standby
on the front
transfer mode: bin
8. If necessary, reconnect the cables to the Interface
settings to be lost. You must reconfigure the
control panel
g. Enter the following command to copy the firmware
Manager card exactly as they were before.
Interface Manager card after replacing the
of the library
file to the temporary location in the Interface
9. Refer to the “Initial configuration steps” section
CompactFlash card. These configuration
to place the
Manager card’s memory:
of the HP StorageWorks Interface Manager and
settings are listed in the “Initial configuration
library off-line. Verify that the control panel indicates
put
Command View TL User Guide for instructions on
steps” section of the HP StorageWorks
System Off-line.
where
how to reconfigure the Interface Manager card.
Interface Manager and Command View TL
b. Check the Overview screen of the control panel to
file.
Because configuration information is stored on the
User Guide. If possible, write down all of
verify that the gripper is empty. If there is a tape
h. Use the quit command to logoff the ftp session.
CompactFlash card, the previous configuration is
the current configuration settings from the
cartridge in the gripper, perform a move command to
lost when the CompactFlash card is replaced.
place the cartridge in an available storage bin.
Interface Manager card before replacing
c. Switch off the power switch located below the control
the CompactFlash card.
panel.
17
2
3
© Copyright 2005 Hewlett-Packard Development Company, L.P.
Second Edition (March 2005)
Part Number: 368006-002
Verify that all access panels are closed, all back
panel cable connections are firmly in place, and all
doors are closed.
Open the center back access door or the right back
access door of the library, depending on the model.
*368006-002*
Turn off both circuit breakers on the AC power
distribution assembly, located in the base of the library
368006-002
cabinet behind the rear access panel. Loosen the two
Make a note of where each cable is connected, and
captive screws at the top of the electronics bay frame
then disconnect all cables from the Interface Manager
and carefully tilt the electronics bay outward.
card.