Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
This plug wi fit in a polarized outlet only one way. If the plug does not fit fufy In the outlet reverse the plug. If it still does not fit contact a qualified electrician to install the proper outleL Do not change the plug in any way. SAVE THESE INSTRUCTIONS FOR HOUSEHOLD USE ONLY Commercial use of this unit voids the manufacturer's warranty. 1 SETUP Powerful Steam Jets O Crease Making Tool ► Attach to the syeamer head to use with shirt cuffs and cottars and/or creating creases in pants. Unt Removal Brush ► Attach to the syeamer head to remove dust or lint attached to clothing. ► Attach to the steamer head to use when tidying clothing Crease Clip ► Use to make creases »n dress shirts andtor pants. Pressing Glove ► Make sure to put on the pressing glove when using this product (Exercise care as exposure in excess of one minute of the pressing glove to steam can result m bum injuries). Align properly from the bottom and press firmly to hear a snapping sound as it fastens into place. 2 ASSEMBLY @ Step One - Insert the widest end of the telescoping pole into the main unit and secure It by tightening the nut Bl Step Two - Insert the hanger assembly to the top of the pole. SI Step Three - Insert the hose base into the base unit opening and turn it clockwise until In place. | Step Three 0 Step Four - Secure the steam head in place between the prongs, then adjust the height using the dips along the telescopic pole. Turn the plastic screw to secure. PRE-USE INSPECTION ■ Check to see if any water is leaking from the excess water removal vah/e. » Firmly shut the excess water removal vaive. B When Inserting the water tank into the main unit make sure the water has not overflowed. «Make sure the power is off. (Note: If water overflows, contact the HAAN Customer Care). 3 BRUSH ASSEMBLY * Lint Removal Brush Assembly »Bristle Brush Assembly ■ Fasten lightly to the emissjon area 9 Push in the direction of the arrows to fasten completely. ■ Fasten bghtty to the emission area 9 Push m the direction of the arrows to fasien completely. • Crease Making Tool Assembly & Usage ■4HI I Fasten the crease making tool into the slot [After Fastening 1 Place a pressing glove on the left hand and fix the sleeve into the desired position. Affix the crease chp to the sleeve near the shoulder, and then use the crease making tool to create a crease. * Refer to the left image. WATER DRAINING 1. Cool the garment steamer for at least 30 minutes after each use 2. Open the excess water removal valve and empty any water remaining in the heater of the main irtt 3. Clean and remove water from the area between the main unit and the water tank to prevent buildup. 4 STEAM PRESS USAGE [ij FI the water tank to the level acoording to the desired usage bme A full water tank is capable of continuous steam release for 100 minutes [g Hold the water tank by its handle and insert securely «>lo the slot in the main unit Align the water refill valvo cap properly and screw securely shut Steam can be released 40-50 seconds after pressing the power button. Pressing the power button again turns the power off. Refill the water tank with water whon the water ref» lamp turns on. Before use Please read the instructions for use and Important Safety Instructions carefully. - Remove any packaging from the appliance. -DO NOT PLUG IN OR TURN ON UNTIL ASSEMBLY IS COMPLETE. • Press the hose guide in the direction of the arrow and turn dockwise until fastened. • Steam can be released 40-50 seconds after pressing the power button; pressing the power button once more turns the power off. • Place the handle on the exclusive hanger stand so that the hose is well extended. The normafy stiff hose becomes highly flexible when steam is emitted, making It easier to use. 5 EFFICIENT GARMENT STEAMING • Extend both sides of the hanger. Turn the grooved tubes on each side of the support to fasten, then hang the steam head between the prongs at the top. • Align the shoulders of the garment on the hanger and allow it to hang freely. • When pressing cfothlrvg. temperature, humidity and pressure are Important Because the steam released is of high temperature (212®f), temperature and humidity conditions for easy pressing are sufficient. Since clothing is hung from the support and hangs freely. the prossuro on the garment may be weak. Thus, one hand should control the handle of the steam head and the other hand should be placed in the pressing glove, as shown in the Image, to hold the garment steamer and allow for pressure to be applied. The hand holding the handle and hand holding the garment should move in unison to facilitate quick and easy pressing. As with regular ironing, the steam pressing process requires some getting used to. Practice by repeating the process a number of times can quickly facilitate easy steam pressing. When pressing dothmg, move the handle lightly In upward and downward movements onty. (Note: Shaking the ...
Otros modelos de este manual:Planchas - Garmet Steamer GS-20 (515.73 kb)