Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
6. Slide the Water Fill Cover toward the iron handle. USING AS A STEAM IRON See Before Using For The First Time. 1. Position the Temperature Control to the OFF position (see Figure 7). 2. Unplug the iron from the outlet. 3. Fill the Water Tank with water; see FILLING THE WATER TANK. 4. Stand the iron on its heel in an upright position on a heat resistant surface. Plug into a 120 V ~ 60 Hz outlet. 5. Turn the Temperature Control to the wool setting or higher. Do not use the steam function with the Temperature Control selected below the wool setting. 6. Tilt the iron to the horizontal position (see Figure 5) to turn the iron on. It may then be returned to the vertical position (see Figure 6) to preheat the iron. 7. Allow approximately 45 seconds for the iron to reach the desired temperature. The red Power On/Heating Light will turn off. The light will continue to turn off and on during use to maintain the proper temperature. 8. Move the Variable Steam for more steam. 9. When finished, turn the Temperature Control to the OFF position, turn Variable Steam to the no steam position and unplug iron. Allow iron to cool before cleaning the exterior of the iron for storing. CAUTION: AVOID COMING IN CONTACT WITH ESCAPING STEAM. FIGURE 8 9 OPERATING INSTRUCTIONS (Cont.) OPERATING INSTRUCTIONS (Cont.) For a penetrating burst and to smooth difficult wrinkles, the Burst of Steam Button (red Power On/Heating Light best results. Do not press the Burst FIGURE 9 Button more than three times successively. Pause for at least 5 seconds to let the For maximum steaming, keep the Water SPRAY For a mist of water to moisten the dry and difficult fabrics such as linen, cotton or wool, or to handle stubborn wrinkles, aim the Spray Nozzle and press the Spray Button (see FIGURE 10). The spray function FIGURE 10 is also handy to moisten creases accidentally ironed into the fabric. The spray function can be used on any and does not affect the ironing temperature. NOTE: You may have to pump the Spray Button several times the first time you use the iron each session to start the spraying action. USING THE VERTICAL STEAM FUNCTION The vertical steam feature allows you to eliminate wrinkles from drapes without having to take them off the rod or to freshen the appearance of clothing on the hanger. 1. Unplug the iron from the outlet. 2. Position the Temperature Control to the OFF position. 3. Fill the water tank with water, see FILLING THE WATER TANK. 4. Stand the iron on its heel in an upright position on a heat-resistant surface. Plug into 120 V ~ 60 Hz outlet. FIGURE 11 10 OPERATING INSTRUCTIONS (Cont.) OPERATING INSTRUCTIONS (Cont.) 5. Move the Temperature setting. 6. Allow approximately 45 seconds temperature. The red Power On/7. Hold the iron 7-15 inches away burst of steam button once. 8. Wait a few seconds before pressing the again. The red Power On/Heating Light during this process. Do not press the burst of than three times successively when the red Power is ON. For best results, keep Water Tank at least 9. When finished, move Temperature Control to the OFF Variable Steam to no steam position and unplug the iron. iron to cool before cleaning the exterior of the iron for storing. CAUTION: AVOID COMING IN CONTACT WITH ESCAPING STEAM. EMPTYING THE WATER TANK The Water Tank should be emptied after each use. 1. When finished, move Temperature Control to the OFF position and turn the Variable Steam to no steam position and unplug the iron from the electrical outlet. 2. Hold the Iron upside down and gently shake it to remove the remaining water in the tank. 3. Press the Burst of Steam and Spray Buttons to release any remaining water. FLUSHING Flushing the iron is advised after every 5 uses or more regularly to prevent harmful mineral build-up that can clog the iron and prevent it from heating and steaming properly. 1. Fill the Water Tank half full; see FILLING THE WATER TANK. 2. Stand the iron on its heel in an upright position on an iron-safe, heat resistant surface. Plug into a 120 V ~ 60 Hz outlet. 3. Move the Temperature Control to the maximum setting. 11 OPERATING INSTRUCTIONS (Cont.) OPERATING INSTRUCTIONS (Cont.) 4. The red Power On/Heating reached the desired setting. 5. Wait for one more cycle, the on and back off again. 6. Move the Temperature Control to 7. Unplug cord from outlet. 8. Steam and hot water will flow through Steel Soleplate, washing away the scales built-up in the iron. 9. Gently move the iron back and forth until the Water 10. Press the Variable Steam Button and turn the Variable no steam position. USER MAINTENANCE INSTRUCTIONS This appliance requires little maintenance. It contains no user serviceable parts. Do not try to repair it yourself. Refer it to a qualified appliance repair technician if servicing is needed. CARE AND CLEANING CAUTION: Unplug the iron from the electrical outlet and allow to cool before cleaning the exterior of the iron and storing. Never immerse the iron in water. NOTE: Do not put any chemical ...
Otros modelos de este manual:Planchas - WST5001ZE (184.59 kb)