Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
with store-bought • Heat concentrates the elements contained in water during evaporation.The distilled or types of water listed below contain organic waste or mineral elements that can demineralised water in cause spitting, brown staining, or premature wear of the appliance: water from the following clothes dryers, scented or softened water, water from refrigerators, batteries or proportions : - 50% tap water, air conditioners, pure distilled or demineralised water or rain water should not be -50% distilled or used in your Tefal iron. demineralised water. Filling the water tank Fill the tank up to the • Check that the Ultracord system is properly locked. “MAX”. • Unplug your iron before filling it. GB Never fill the • Set the steam control to “0” – fig.1. appliance by holding • Take the iron with one hand and tilt it slightly, with the nose of the soleplate it directly under the tap. pointing down. • To open the flap of the water tank, push the button – fig.2. • Fill the tank up to the “MAX” line – fig.3. • Close the flap of the water tank, until it clicks into place. Use Adjust the temperature and the steam • Set the thermostat control – fig.4, referring to the table below. • The thermostat light comes on. It will go out when the soleplate is hot enough – fig.5. FABRIC POSITION OF THERMOSTAT CURSOR STEAM SETTING POSITION LINEN COTTON WOOL SILK SYNTHETIC (Polyester,Acetate, Acrylic, Nylon) MAX ••• •• • 0 = STEAM ZONE RECOMMENDATIONS • Your iron heats up quickly: so begin by ironing fabrics that are ironed at low In order to avoid water temperatures first, then go on to those requiring a higher temperature, dripping from the iron onto the linen: • If you turn down the thermostat, wait until the thermostat light comes back on - Turn off the steam before beginning to iron again, when ironing silk or • When ironing fabrics with mixed fibres, set the ironing temperature for the most synthetic fabrics. delicate fibre. For delicate fabrics we recommend testing the fabric first on an - Set it at the minimum inconspicious place eg (inside the hem). position for wool. Spray Function Make sure that there • Whether steam or dry ironing, you are able to use the spray button to dampen is water in the tank laundry to remove stubborn creases – fig.6. before using this button. Obtain more steam • Press the Turbo button from time to time – fig.7. • Wait a few seconds between each shot before pressing the Turbo button again. Vertical steam ironing Hold the iron a few • Hang the garment on a hanger and hold the fabric slightly taut with one centimetres from the hand.The steam is very hot, so you should always do this with the garment on a fabric to avoid burning hanger – never iron clothes which someone is wearing. delicate fabrics. • Set the thermostat control to “MAX” – fig.8. • Press the Turbo button repeatedly – fig.7 moving the iron from top to bottom – fig.9, wait a couple of seconds between each use of the button. Dry ironing • Set the temperature for the fabric to be ironed. • Set the steam control to “0” – fig.1. • You may start ironing when the thermostat light goes out. Extra Functions Ultracord System (depending on model) Your iron has been designed with the Ultracord system to prevent the steam cord from dragging across the linen and creasing it while ironing. It also allows you to handle the iron more easily. To use the Ultracord system: • Turn the Lock-System ring and put the indicator on the position – fig.10. • The Ultracord system opens out automatically. You can now plug in your appliance and begin to iron. • Each time you put your iron on its heel, the Ultracord system closes automatically and opens out each time you pick the iron up again....
Otros modelos de este manual:Planchas - FV5210 (1.73 mb)
Planchas - FV5250 (1.73 mb)
Planchas - FV5260 (1.73 mb)