Votos - 5, Puntuación media: 4.6
(
)
)
|
Resumen del manual
• Steam output control dial setting: -Thick fabric: increase the steam setting. -At a low temperature : set the steam output control dial to the low position. To prime the steam circuit, either before using the iron for the first time, or if you have not used the steam function for a few minutes, press the steam control button several times in a row, holding the iron away from your clothes. This will enable any cold water to be ejected from the steam circuit. 7-WHEN THE RED LIGHT “WATER TANK EMPTY” COMES ON There is no more steam.The removable water tank is empty. 1. Grasp the handles of the removable tank and pull horizontally to remove it; fill with water. 2. Replace and push it firmly into place. 3. Press the “restart” button on the control panel to continue ironing (12). 12 8- VERTICAL STEAM IRONING 1. Set the iron temperature control slide and the steam output control dial (located on the control panel) to the MAX position. 2. Hang the garment on a coat hanger and hold the fabric slightly taut with one hand. As steam is very hot, never attempt to remove creases from a garment while it is being worn, always hang garment on a coat hanger. 3. Holding the iron in a vertical position, tilted slightly forwards, press repeatedly on the steam control button (under the iron handle) moving the iron from top to bottom (13). Recommendations : for fabrics other than linen or cotton, hold the iron a few centimetres from the garment to avoid burning the fabric. 13 9- TURBO STEAM FUNCTION (depending on the model) Press 2 or 3 times on the turbo steam button to obtain a more powerful burst of steam (14): • for ironing thicker fabrics, • to eliminate creases, • for powerful vertical steaming. Be careful : use the turbo steam function very carefully because of the exceptional power of steam that may cause burns. NOTE : continuous use of the turbo steam function will begin to cool the iron and may cause water to drip from the iron. If this occcurs, stop using the turbo steam function and allow the iron thermostat to reach temperature again (thermostat light will come on and go off) before using this function again. 14 9- TURBO STEAM FUNCTION (depending on the model) Press 2 or 3 times on the turbo steam button to obtain a more powerful burst of steam (14): • for ironing thicker fabrics, • to eliminate creases, • for powerful vertical steaming. Be careful : use the turbo steam function very carefully because of the exceptional power of steam that may cause burns. NOTE : continuous use of the turbo steam function will begin to cool the iron and may cause water to drip from the iron. If this occcurs, stop using the turbo steam function and allow the iron thermostat to reach temperature again (thermostat light will come on and go off) before using this function again. 14 10- MAINTAINING YOUR STEAM GENERATOR • Before cleaning, ensure that your steam generator is unplugged and that the soleplate and the iron rest have cooled down. • Do not use detergent or descaling products for cleaning the soleplate or the base-unit. • Never hold the iron or the base unit under the tap. • Do not place the iron on a metal rest as this could damage it. Place it on the iron-rest on the base unit : it has non-slip pads and has been designed to withstand high temperatures. 1. Empty and rinse the removable water tank (15). 2. Regularly clean the soleplate with a damp, non-metallic washing up pad. 3. Clean the plastic parts of the appliance occasionally with a soft cloth. 15 11. THE ORANGE “BOILER RINSE” LIGHT FLASHES 1. TO RINSE THE BOILER USING RINSING ACCESSORY Note: • To extend the efficient operating life of your boiler and avoid scale particles on your linen, your generator is equipped with an orange “boiler rinse” warning light that flashes on the control panel after about 10 uses. • If your water is hard, increase the frequency. • Do not use descaling agents for rinsing out the boiler, as they could damage it. For greater effectiveness and for ease of operation, you are advised to use the rinsing accessory provided in the box. It will make it easier to rinse the boiler as the generator will need less handling. (a) (b) 12 12- PUTTING YOUR STEAM GENERATOR AWAY 1. Place the iron on the rest. 2.Turn off at the main O/I switch and unplug. 3. Raise the retaining hoop over the iron until it locks into place (audible click) (21).Your iron is then safely retained on its base. Warning: do not touch the soleplate while still hot. 4. Retract the electric supply cord (22). 5. Allow the iron (and iron rest) to cool for 30 minutes. 6. You can then put your steam generator away, carrying it by the handle (23). Your rinsing accessory has been designed to work on a wide range of taps. It is supplied with 2 types of membrane (a) (b). Choose the one best suited to your tap. If you do not wish to, or cannot use the rinsing accessory, refer to the advice in paragraph II (below). Before attempting to rinse the boiler of your generator, it is essential to leave it ...
Otros modelos de este manual:Planchas - PRO EXPRESS TURBO (613.24 kb)