Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
If you turn the control dial down from a hot setting to a cooler setting, wait until the iron temperature has stabilised before you continue ironing. fl ‡ · ‚ 400 350 300 . ¤ ‹ › fi „ ‰ UK Helpline 0844 871 0953 Replacement Parts 0844 873 0719 Ireland Helpline 1800 409 119 40652 rev1 23/4/08 17:52 Page 4 5 FILLING A 1 Make sure that the iron is not plugged in and then set the variable steam control ‹ to the ‘0’ position before filling the iron with water. 2 Open the fill cap and pour water through the filling hole › into the water tank ·, using the beaker provided, one beaker full of water fills the tank (400ml). A After filling, replace the fill cap. In hard water areas, the use of distilled or demineralised water is recommended. Never use battery topping up fluid or water containing any substances like starch, or sugar, or defrosted water from a refrigerator. 3 Always pour out the remaining water after use. Warning: When filling your iron with tap water, always use the beaker provided. Never fill directly under the tap. Temperature control B Plug in the iron and switch on. The ‘power on’ indicator lights „, situated in the back cover, will illuminate. Set the temperature control dial B to the temperature required, but don’t start ironing immediately. If you wait a few minutes, the iron will stabilise at the required setting. Your Morphy Richards iron is fitted with an indicator light ‡ which will go on and off while you are ironing. This is perfectly normal as it shows that the iron is maintaining the heat setting you have chosen. It is always a good idea to begin with cool fabrics and work up to higher settings. An iron heats up quicker than it cools down so you’ll save time and electricity. FEATURES OF YOUR IRON Temperature indicator light The indicator light under the control knob shows that the iron is warming up. When the required temperature is reached, the light will go out and will cycle on-off during operation. Dry ironing You can use your iron as a dry iron only. Make sure the variable steam control ‹ is set to the ‘0’ symbol. Any temperature setting may be used depending on the garment. The spray feature may be used provided there is water in the tank (see ‘Filling’ section). You do not need to put any water in the tank when dry ironing only. Spray C Press the spray button ¤ and aim the spray of water at stubborn creases. You can do this whilst dry ironing, providing there is water in the tank. When using the water spray it may be necessary to push the button a few times to get the spray pump primed. Variable steam D Fill the iron with water as described in ‘Filling’, and insert the plug into the electrical socket. The steam output can be varied from low to high by sliding the variable steam control D. When using the iron at the bottom of the steam range, the steam output should be adjusted to the lowest setting. The steam facility should only be used on garments which are suitable for ironing within the steam band. Steam uses additional energy. To save energy, only use steam when necessary. A Min Max Silk Nylon Wool Cotton Linen B C D lower steam 2 dot higher steam 3 dot 40652 rev1 23/4/08 17:52 Page 5 6 Shot of steam E Press the shot of steam button . to obtain a burst of extra steam for ironing out creases in heavy material such as denim etc. The shot of steam can be used whilst dry ironing, providing there is water in the tank, and the temperature control is set within the steam range. Do not use shot of steam at temperatures below the steam range shown on the control. Note: For optimum steam quality, do not operate the shot more than three times in succession. Vertical steam Hold the iron in a vertical position between 1cm and 2cm away from the item F. Press the shot of steam button ., this will create vertical steam. This feature is especially useful for removing creases from hanging clothes, curtains, wall hangings, etc. Note: For optimum steam quality, do not operate the shot more than three times in succession. No drip system Your iron is fitted with a no drip system which is designed to prevent water escaping from the soleplate when the iron is too cold. During use, the no drip system may emit a loud click, particularly during heat-up or whilst cooling down. This is perfectly normal and indicates that the system is functioning correctly. Auto energy shut-off Energy conscious iron with no compromise on performance... Your iron is fitted with the auto energy shut-off function, and will automatically shut down after a set period. If the iron is left unattended in the horizontal position, it will shut down after one minute. If it is left in the vertical position, it will shut down after 3 minutes. When this happens, the two ‘power on’ lights, situated in the back cover „, will flash to show that the iron is in power-off mode. It stops when you stop... To reactivate the iron, gently shake it until the ‘power on’ lights „ stop flashing and remain on. The iron will then start to heat back up...