Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
If you are unable to use de-mineralized or distilled water, we recommend you use this procedure monthly to help avoid mineral build-up: 1. Set Lighted On/Off Switch to “Off” position and unplug power cord from electrical outlet. Allow unit to completely cool. 2. Remove Fabric Brush from Steam Nozzle (if connected). 3. Remove Water Reservoir Cap and drain remaining water from water reservoir into sink or tub. 4. Using Measuring Cup, make a mixture of 8 oz. (237 ml.) vinegar and 8 oz. (237 ml.) 5. Slowly pour water-vinegar solution into water reservoir through Water Reservoir Inlet. Replace Cap. 6. Plug unit in and allow to heat up. Press the Steam Button for several minutes to allow water- vinegar solution to clear Steam Nozzle of mineral deposits. 7. Unplug unit and allow to cool before draining any remaining water-vinegar solution from water reservoir. 8. Once water reservoir is empty, refill with 16 oz. (473 ml.) of fresh water and repeat STEP 7. Repeat as necessary until vinegar odor dissipates. 9. Once odor is eliminated, make sure water reservoir is empty and replace Water Reservoir Cap. PROPER STORAGE Preparing your Fabric Steamer & Iron for storage is quick and simple. When you have finished your steaming tasks, follow the steps listed below. 1. Set Lighted On/Off switch to “Off” position and unplug power cord from electrical outlet. 2. Allow unit to cool completely (at least 30 minutes). 3. Remove Fabric Brush from Steam Nozzle (if connected). 4. Remove Base Unit from Wall-Mounting Base (if it is mounted), and drain any water remaining in water reservoir into a sink or tub. 5. Mount Base Unit back onto Wall-Mounting Base, and wrap power cord around base. Place Steam Nozzle onto Steam Nozzle Hanger. 6. Alternatively, store Base Unit (with Steam Nozzle) in a safe, convenient location. Top Innovations, Inc. FABRIC STEAMER & IRON PRODUCT INFORMATION USING THE FABRIC STEAMER & IRON STEAMING GARMENTS The following features Carefully inspect Styrofoam packing To obtain possible missing parts, 1. Place garment on a clean, Hang within easy reach of to the Customer Support section on page 14 of this manual. Hose / Nozzle. 2. Point Steam Nozzle at bottom of Steam will rise along inside and fabric, removing wrinkles. Slowly slide Steam Nozzle vertically, from bottom to top of garment. NOTE: Do not allow kinks to form in hose 3. Direct Steam Nozzle away from garment and smooth 4. Repeat steps 3 and 4 as necessary until fabric is smooth USING THE IRONING PLATE Whenever a crisp crease is desired, this can be easily accomplished A folded towel placed on a table-top or other flat surface may be used is not conveniently available. 1. Be sure Fabric Brush has been removed before proceeding. CAUTION: Use care when removing Fabric Brush from Ironing Plate, as both may be hot and may cause burns or other injury. 2. If the unit has not recently been in use, allow Ironing Plate at least 45 seconds to heat up. 3. To form a crease, fold fabric and apply Iron Plate as you would use a regular iron. If a steam burst is desired, simply press Steam Button. When you are finished using the Fabric Steamer & Iron, immediately set Lighted On/Off switch to “Off”position and unplug power cord from electrical outlet. Refer to Care and Storage Guidelines on page 13 of this manual for proper cleaning and storage procedures. 12 Top Innovations, Inc. 5 UNIT FEATURES &ACCESSORIES 1. WALL-MOUNTING BASE 2. BASE UNIT 3. WATER RESERVOIR FILL HOLE 4. WATER RESERVOIR CAP 5. WATER LEVEL WINDOWS 6. LIGHTED ON/OFF SWITCH 7. STEAM NOZZLE HANGER 8. STEAM NOZZLE 9. HEATING INDICATOR LIGHT 10. STEAM BUTTON 11. HANDLE 12. IRONING PLATE 13. STEAM HOSE 14. FABRIC BRUSH 15. MEASURING CUP Top Innovations, Inc. FABRIC STEAMER & IRON PRODUCT INFORMATION USING THE FABRIC STEAMER & IRON • The Wall-Mounting Base (1) attaches to the wall Base Unit, saving space and providing • The Base Unit (2) is the main body of the accessed for filling via the Water Reservoir Inlet. • The Water Reservoir Inlet (3) serves as the opening through the water reservoir. The Water Reservoir Cap must be removed in order to access Inlet. • The Water Reservoir Cap (4) covers the Water Reservoir Inlet, keeping water contained safely inside the water reservoir. • The Water Level Windows (5) provide a convenient view into the water reservoir, allowing the remaining water level to be easily monitored. • The Lighted On/Off switch (6) activates and deactivates the unit, and provides a clear visual indication of whether or not the unit is powered on. • The Steam Nozzle Hanger (7) provides a safe and convenient place to hang the Steam Nozzle when not in use. • The Steam Nozzle (8) emits a flow of hot, penetrating steam when the Steam Button is pressed. • The Heating Indicator Light (9) illuminates when the unit is turned on, indicating that the heater is active. The Light will deactivate once the Ironing Plate is heated, then cycle on and off during use as the unit works to maintain a constant tem...
Otros modelos de este manual:Planchas - SF-432 (273 kb)