Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
•WARNING: when not in use, your iron should never be placed flat and left on an ironing board. •To prevent damage to the textile being ironed, follow the temperature guide carefully. (Test the inside of the hem of the garment). • When ironing is complete, remove the plug from the socket, empty any remaining water from the tank, and allow to cool before storage. • If you drop or severely knock your iron this could cause internal damage even if the outside appears alright. Have it checked by a qualified electrician. • It is recommended that you use up one beaker of water by operating your iron’s steam and shot of steam functions before ironing any clothes as some dripping may occur while your irons steam system is activated. 2 turbo steam RN40655 Rev 1 23/7/04 1:34 PM Page 3 Electrical requirements Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply which must be A.C. (Alternating current). If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted. Instructions for use WARNING : The plug removed from the mains lead, if severed, must be destroyed as a plug with a bared flexible cord is hazardous if engaged into a live socket outlet. Should the fuse in the 13 amp plug require changing a 13 amp BS1362 fuse must be fitted. WARNING: THIS APPLIANCE MUST BE EARTHED. Temperature guide Heat setting markings on the adjustable control dial of all Morphy Richards irons match those of the International Textile Care Labelling Code. Symbol (120.C Max) Cool (160.C Max) Warm (210.C Max) Hot Control knob Do not positions iron at all Fabric Nylon, Acetates Wool, Polyester Cotton, Linen e.g. Acrilan mixtures e.g. Rayon, Rayon Courtelle, Orlon Polyester/Cotton mixtures, Triacetates, e.g. e.g. Rayon/Linen Tricel/Polyester Ironing Iron on wrong side Fabrics requiring this if moisture required setting usually require use damp cloth steam pressing for heavy (Not Acetate) cotton, denim etc. Dry and spray Steam/spray/shot of steam Jet clean With water in tank Without water in tank Dry ironing 3 turbo steam RN40655 Rev 1 23/7/04 1:34 PM Page 4 Components of your Filling iron 1 Make sure that the iron is not plugged in and then set the variable steam control ‹ to the ‘0’ position before filling the iron with water. 2 Open the fill cap and pour water through the filling hole › into the water tank ·, using the beaker provided, one beaker full of water fills the tank (400ml). A After filling replace the fill cap. In hard water ‚ areas the use of distilled or demineralised water is recommended. Never use battery topping up fluid or water containing any substances like ‡· starch, or sugar, or defrosted water from a refrigerator. 3 Always pour out the . Shot of steam button remaining water ¤ Spray button ‰ after use. Warning: ‹ Variable steam control When filling your › Filling hole with cap iron with tap water fi Spray nozzle always use the fl Soleplate beaker provided. ‡ Illuminated temperature control dial Never fill directly · Water tank under the tap. ‚ Life long anti-scale (certain models only) „ Power on indicator lights - Auto shut-off indicator (certain models only) Temperature control ‰ Filling beaker Plug in the iron and switch on. The Before use ‘power on’ indicator lights „ situated in the back cover will illuminate. Set the Note: The steam facility should only be temperature control dial B to the used on garments which are suitable for temperature required, but don’t start ironing ironing at the 2 and 3 dot settings. immediately. If you wait a few minutes, the When ironing with the steam facility at the iron will stabilise at the required setting. Your 2 dot setting, the steam output should be set Morphy Richards iron is fitted with an at the lower end of the steam range (see indicator light ‡ which will go on and off variable steam section). while you are ironing. Textiles and clothes are supposed to B carry ironing instructions. If they don’t you should follow the fabric guide on page 3, but be sure to test the temperature by ironing the hem of the garment or similar area first. If you turn the control dial down from a hot setting to a cooler setting, wait until the iron temperature has stabilised before you continue ironing. 4 .¤ ‹ › fi fl „ A turbo steam RN40655 Rev 1 23/7/04 1:34 PM Page 5 This is perfectly normal as it shows that the iron is maintaining the heat setting you have chosen. It is always a good idea to begin with cool fabrics and work up to higher settings. An iron heats up quicker than it cools down so you’ll save time and electricity. Features of your iron Temperature indicator light The indicator light under the control knob shows that the iron is warming up. When the required temperature is reached the light will go out and will cycle on-off during operation. Dry ironing You can use your iron as a dry iron only. Make sure the variable steam control ‹ is set to ...