Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Note; For optimum steam quality, do not operate the shot more than three times in succession. D No drip system Your iron is fitted with a no drip which is designed to prevent water escaping from the soleplate when the iron is too cold. During use, the no drip system may a loud click, particularly during heat-whilst cooling down. This is perfectly normal and indicates that the system is functioning correctly. Auto shut-off Your iron is fitted with the auto shut-off function it will automatically shut down after a set period. The ‘safety switch off’ led will flash on the function panel. If the iron is left unattended in the horizontal position it will shut down after 30 seconds. If it is left in the vertical position it will shut down after 8 minutes. To reactivate the iron gently shake it and wait for the iron to heat-up as normal. Life long anti-scale system The life long anti-scale system reduces scale deposits and helps prolong the life of the iron. Electrical requirements Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply which must A.C. (Alternating current). If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted. Instructions for use WARNING : The plug from the mains lead, if severed, must be destroyed as a plug with a bared flexible cord is hazardous if engaged into a live socket outlet. Should the fuse in the 13 amp plug require changing a 13 amp BS1362 fuse must be fitted. WARNING: This appliance must be earthed. Temperature guide Heat setting markings on the function console panel of your Morphy Richards irons match those of the International Textile Care Labelling Code. Symbol (120.C Max) Cool (160.C Max) Warm (210.C Max) Hot Control knob Do not positions iron at all Fabric Nylon, Acetates Wool, Polyester Cotton, Linen e.g. Acrilan mixtures e.g. Rayon, Rayon Courtelle, Orlon Polyester/Cotton mixtures, Triacetates, e.g. e.g. Rayon/Linen Tricel/Polyester Ironing Iron on wrong side Fabrics requiring this if moisture required setting usually require use damp cloth steam pressing for heavy (Not Acetate) cotton, denim etc. Dry and spray Steam/spray/shot of steam Jet clean With water in tank Without water in tank Dry ironing 6 3 Job: Components iron ‡ · ‰ . ¤ ‹ ‚ › fi „ fl . Variable steam button ¤ Shot of steam button ‹ Spray button › Filling hole with cap fi Spray nozzle fl Soleplate ‡ Temperature console · Water tank ‚ Life long anti-scale (certain models only) „ Filling beaker ‰ Auto shut-off indicator Before use Note: The steam facility should only be used on garments which are suitable for ironing at the 2, 3 dot settings. When ironing with the steam facility at the 2 dot setting, the steam output should be set at the lower end of the steam range (see variable steam section). Textiles and clothes are supposed to carry ironing instructions. If they don’t you should follow the fabric guide on page 3, but be sure to test the temperature by ironing the hem of the garment or similar area first. If you adjust the temperature from a hot setting to a cooler setting, wait until the iron temperature has stabilised before you continue ironing. It is always a good idea cool fabrics and work up An iron heats up quicker than it down so you’ll save time and Filling 1 Make sure that the iron is not plugged in and then set the variable steam control . to the ‘0’ position before filling the iron with water. 2 Lift up the fill cap and fill the water through the filling hole › into the water tank · , using the beaker provided. A 1 beaker fills the tank (400ml). After filling replace the fill cap. In hard water areas the use of distilled or demineralised water is recommended. WARNING: Never use battery topping up fluid or water containing any substances like starch, or sugar, or defrosted water from a refridgerator. 3 Always pour out the remaining water after use. WARNING: When filling your iron with tap water always use the beaker provided. Never fill directly under the tap. A Temperature control B Increase temperature Decrease temperature • Default setting + 3 dot (cotton) • To increase temperature press the top button. • To decrease temperature press the bottom button. • The light panel will flash to indicate that the iron has not yet reached the correct temperature. • Once the correct temperature has been reached , the light will stop flashing and there will be one ‘beep’ to signal that the iron is now ready for use. Features of your iron Dry ironing You can use your iron as a dry iron only. Make sure the variable steam control . is set to the ‘0’ symbol. Any temperature setting may be used depending on the garment. The spray feature may be used provided there is water in the tank (see filling section). You do not need to put any water in the tank when dry ironing only. Spray Press the spray button ‹ and aim the spray of water stubborn creases. You can do this whi...