Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
It will be accompanied by a clicking noise which is quite normal. 8 Begin first time ironing with an old towel. It takes one minute to reach the required temperature. 9 Press the steam button for steam ironing. 10 To switch the unit off, turn the power switch on the base unit to ‘O’ (OFF). Dry ironing 1 Connect the appliance to a suitable mains outlet. 2 Turn the temperature dial on the iron in a clockwise direction, select dot-1, dot-2 or dot-3 according to the recommendation of the garment label. 3 The temperature indicator light glows on the iron, indicating that it is switched on. 4 When the required temperature is reached, the temperature indicator light on the iron goes off. The iron is then ready to use. It is always a good idea to begin with ’cool’ fabrics and work up to higher settings. An iron heats up quicker than it cools down, so you’ll save time and electricity. Steam ironing 5 D The spray unit (certain models only) The spray unit can be used at any time and does not affect any product settings. C 42271 rev4 30/7/08 15:56 Page 5 Filling the spray unit The spray feature ‰ is lightly secured to the handle. To fill the water tank, pull the spray unit forward using the two moulded lugs provided. Remove the spray bottle A from the base of the pump and fill with water to the ‘MAX’ mark. Re-fit the spray bottle, making sure the arrows (printed black) are in line. To replace the spray unit Align the spray unit with the front of the iron. Fit the bottom location leg into the slot at the front of the handle. Pivot the spray unit towards the iron, making sure it clips firmly in place. Anti-scale system The anti-scale cartridge is designed to reduce the build-up of limescale which occurs during steam ironing, this will prolong the working life of your iron. However, please note that the anti-scale cartridge will not completely stop the natural process of limescale build-up. Replacing your anti-scale cartridge How often you need to replace your antiscale cartridge depends on how often you use your iron with it’s steam functions and how ‘hard’ your water supply is. Water hardness varies greatly from one area to another. For advice on the relative hardness of your water, contact your local water supplier. If you spend an average of two hours per week ironing, then we suggest you refill your anti-scale cartridge as shown below: If you iron more or less frequently, then you should alter the interval between refills accordingly. Replacement anti-scale refills To obtain replacement anti-scale refills, telephone our spares number on: 0844 873 0719. 1 If a new cartridge is not available, you may continue operating the appliance but scale will build up in the system. Replace the used cartridge as soon as possible. 2 Disconnect the appliance from the mains outlet. 3 Slide out the tank and remove the anti-scale cartridge as shown E. 4 Pull the plate from the end of the cartridge F. 5 Remove the foam pad G. 6 Place the refill into the cartridge, reposition the foam pad and clip the plate onto the cartridge, making sure it locks in position H. Features of your steam generator Temperature indicator light The indicator light shows that the iron is warming up. When the required temperature is reached, the light will go out and will cycle on-off during operation. Steam function During the steaming process, small amounts of water may be ejected from the soleplate. This is normal and can be avoided by using the steam for short amounts of time and only when the iron is at the correct temperature (the indicator light on the iron goes out when ready). 6 Water hardness Soft Medium Hard Refill interval 6 3 11/2 (months) E F H G 42271 rev4 30/7/08 15:56 Page 6 7 Sudden jolts of the boiler unit can also cause water droplets on the soleplate; therefore, do not move the base unit during ironing. We recommend for the first time ironing that you iron over an old towel. Vertical steam Hold the iron in a vertical position between 1cm and 2cm away from the item I. Press the steam button ., this will create vertical steam. This feature is especially useful for removing creases from hanging clothes, curtains, wall hangings, etc. Emptying and storing When you have finished ironing, unplug your iron. 1 Slide out the water tank and remove the anti-scale cartridge J. 2 Empty the water in the tank by holding it upside down K. 3 Replace the anti-scale cartridge and reinstall the water tank. Unplug the generator and leave the iron to cool off for fifteen minutes minimum. The iron must be placed on the iron rest plate. The iron and boiler can now be stored together. Maintenance To clean a stainless steel soleplate To keep the soleplate of your iron clean and free of limescale, we recommend that you use one of the gentle chrome, silver or stainless steel cleaners that are generally available. Always follow the manufacturer’s instructions. To clean off melted man-made fibres, set the iron at 3-dot position and pass it over a clean piece of cotton, th...