Votos - 3, Puntuación media: 3
(
)
)
|
Resumen del manual
Unscrew the valve in the center of the base and pour water into the opening or hold under a source of running water until the container is filled to the desired level. Replace the valve and return the container to the upright position. Place the water container onto the base and make certain it seats properly into the cavity. DO NOT FILL THE CONTAINER WITH HOT WATER. DO NOT ALLOW THE CONTAINER TO BECOME DRY DURING OPERATION AS THIS WILL SHORTEN THE LIFE OF THE STEAMER STEP 3 -OPERATING THE STEAMER Insure the ON/OFF switch is in the OFF position. Plug the steamer cord into a normal electrical outlet or approved extension cord. Turn the ON/OFF switch to the ON position. The switch will light when electricity is connected. Steam will be produced from the nozzle in a few seconds. PRESSING WITH STEAM 1. Grasp the control handle with the nozzle facing upward. Beginning at the bottom of the fabric will allow the steam to rise inside and outside removing wrinkles. Slowly move the nozzle from the bottom to the top of the fabric. 2. Remove the nozzle from the garment and smooth the fabric with your free hand. NOTE: 1. Pressing will be easier if there are fewer creases in the object to be steamed. 2. Shaking out the article prior to steaming will avoid excess creasing 3. For towels, handkerchiefs and napkins, drape them over a rod or steam press them in place over towel racks. 4. Heavier fabrics may require repeated steaming. Repeat steps one and two as necessary. With practice you will gain speed and efficiency. You will soon learn which fabrics will require multiple steam applications. Accessories Fabric Brush Your steamer is supplied with an accessory fabric brush which can be used to gently brush the knap of fabric such as corduroy. To install simply snap into the appropriate slot in the nozzle when the steamer is off and cool. Don't use the brush on delicate fabrics such as silk or satin Lint Remover The supplied lint removal tool may be used with the steamer or by itself. To install on the steamer make certain the unit is off and cool. Simply snap the tool on the nozzle. Captured lint may be removed by rubbing the surface of the tool with a dry scrap of fabric in the reverse direction from normal use. Squeegee Another feature of steam is the ability to clean. Live steam dissolves greasy film and dirt. To take advantage of this your unit is equipped with a squeegee to allow the cleaning of windows, mirrors and other glass surfaces. To install the squeegee merely snap it into the appropriate slot in the nozzle when your unit is off and cool. CLEANING AND STORING a. Turn the ON/OFF switch to the OFF position and unplug from the power source. b. Wait for the steamer to cool completely for at least 30 minutes. c. Remove and drain the water container. Drain the unit by removing the drain plug and allowing the contents of the, reservoir to drain. Tip the unit in the direction of the drain plug to remove remaining water. Replace the plug. d. Remove the steamer hose and hanger rod. e. Remove the water tank. f. Remove excess water from the reservoir by lifting the unit and pouring. Flush the reservoir area with fresh water to clean any residue from the water source. g. Pour fresh water into threaded pipe of steam hose. Then remove water from reservoir to clean any residue inside the steamer. If there is too much residue, you may use soft water to soak and flush the reservoir. h. Reattach the hose, hanger rod and water container and store the unit. OTHER IMPORTANT NOTES During operation the steamer hose may gurgle. This is a normal result of condensation collecting inside the hose. Simply lift the control handle upward until the hose is extended to its full height. The gurgling will disappear when the excess moisture inside the hose has had a chance to drain back into the base. If the steamer stops producing steam then starts again. You may wish to examine the inside of the reservoir. The most common reason for this effect is the accumulation of sediment from mineral laden water. Clean the offending sediment from inside the unit, first following the steps for cooling and cleaning the unit as presented previously. TROUBLESHOOTING THE STEAMER PROBLEM CAUSE SOLUTION Steamer fails to heat Steamer not plugged in Plug in to electrical outlet Auto shut off engaged check water container is not empty. Reset ON/OFF switch. No steam water level is low Turn ON/OFF switch OFF and refill water container Water drips from nozzle Condensation in hose Hold the hose vertical and allow water to drain back to tank Nozzle gurgles condensation in hose Hold the hose vertical and allow water to drain back to tank Steam is intermittent sediment in container Follow the removing mineral buildup procedure Note: Water chemicals and conditions will vary in different areas. To insure continued operation of the steamer, never store without cleaning and removing excess water from the reservoir and water container. Removing Mineral Buildup One common proble...
Otros modelos de este manual:Planchas - SF-450 (135.13 kb)