Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Move the temperature control dial from ‘MIN’ to ‘Max’ a few times. • Iron may not be hot enough. Set temperature control dial to the ‘Max’ position. Always allow iron sufficient time to heat up (pilot light goes off). • Overuse of steam trigger. Allow more time betweeneach burst. • Iron may have been overfilled. Turn iron off,emptywater and follow instructions for filling. • Steam performance may be low if iron requires seasoning. To season, use regular tap water for 1or 2 tanks until steam performance improves. OPERATING INSTRUCTIONS Before using your iron, check the voltage and type of plug that is required for your location. If necessary, readjust the dual voltage switch according to local voltage - 115/120V, 60 Hz., 230/240V, 50 Hz. This is accomplished by sliding the dual voltage control switch located in the rear of the iron to the coresponding voltage setting. Note: The voltage selector is preset at the factory for use on 115/120V, 60 Hz. N. A. household curent. Caution: Always disconnect the iron before adjusting the dual voltage switch to the corect voltage setting. BEFORE FIRST USE Remove any labels, stickers or tags which may be attached to thebody or soleplate of the garment steamer/ iron before using the appliance. Read all instructions for use carefully. Always follow the Important Safeguards. IMPORTANT The first time an iron is used, some odor and small white particles may come out of the steam vents. This perfectly normal and will cease tooccur after the iron has been in use for a short while. Before you start using your garment steamer/iron, follow the instructions in the manual and do the following in order to eliminate any odor and small white residue particles and to ensure optimum steam performance. • Fill the garment steamer/iron with regular tap water. • Set the temperature control dial to its highest setting. • The pilot light will go off to indicate that the garment steamer/iron has reached the selected temperature. • Keep the iron in a horizontal position and allow it to steam until the water runs out. • Press the steam trigger to eliminate white residue particles. • Repeat this procedure through 2 or 3 fillings. 3 8 IRONING CHART NOTE: Before starting to iron or steam delicate fabrics, it is best to first test the temperature of the garment steamer/iron on a hem or an inside seam. To select garment steamer/iron temperature, align temperature selected on dial with the indicator on the water tank. DIRECTIONSON LABELFABRICTEMP. CONTROLBURST OFSTEAMPlease note that on the label means ‘THIS ARTICLE CANNOT BE IRONED!” COTTONLINENSYNTHETIC FIBERS, e.g.acrylic, nylonpolyesterSILKWOOLMIN• •• •• • MAXSet temperature to "MAX" OPERATING INSTRUCTIONS cont. Using the Garment Brush CAUTION! To prevent the risk of burns, make sure that the iron is not plugged in and that the iron sole plate is not hot before you slide on the garment brush to the iron. 1. Disconnect the garment steamer/iron from the power supply. 2. If the appliance is hot, let it cool down first. 3. Slide the garment brush onto the soleplate of the garment steamer/iron and lock in place by turning the locking tab 180° counter-clockwise. 4. To remove the garment brush, disconnect garment steamer/iron from the power supply and let the unit cool down. 5. Turn the locking tab 180° clockwise and slide the garment brush off. 4 Using the Swivel Handle The handle on the garment steamer/iron can be changed in position by turning the handle 180° counter clockwise. (See illustration at right.) You can use the iron with the handle over it for regular ironing or with the handle behind it for steaminggarments. (See illustrations below. ) OPERATING INSTRUCTIONS cont. 7 DRY IRONING All marked settings on the temperature dial can be used for dry ironing. 1. Plug the cord into a household electrical outlet (see page 3 forvoltage settings). The pilot light light will go “On” , indicating that the iron is heating up. 2. Set Temperature Control Dial to desired temperature setting. 3. Place garment steamer/iron on its heel (on a stable, protected surface) while iron is warming to desired temperature. 4. When the iron has reached the desired temperature, the pilot light will go “ Off”. EMPTYING, CLEANING & STORING THE GARMENT STEAMER/IRON Always empty and clean your garment steamer/iron after each use and before storing. 1. Turn the temperature control dial to the “MIN” position 2. Unplug the power cord from the electrical outlet. 3. Empty the garment steamer/iron of all remaining water in the water reservoir. 4. Allow the unit to cool down before cleaning. 5. When the garment steamer/iron has cooled down completely, scale and other residue can be wiped off the soleplate with a damp cloth. 6. Store the garment steamer/iron in the upright position. WARNING! Use caution when emptying the garment steamer/iron. Burns may occur from touching hot metal surfaces, hot water or steam. Locking Tab OPERATING INSTRUCTIONS cont. SETTING THE IRON TEMPERATURE Filling...