Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
• Water tank may be empty or water level is very low. Add water. • Make sure that the temperature control dial and the variable steam control are correctly set. Formaximum steam, (setting " Max" on steam control), temperature control dial should be set on "• •• ". • Adjustable steam control is set on " 0". Always allow the iron to reach the selected temperature with the adjustable steam control setting at "0". Make sure the temperature control dial is set in the correct steam area, e.g. " • ", and the steam control is noton "0". For more steam, turn temperature dial to higher setting, e.g. "• •• ", and the steam control to "Max". • If temperature setting and steam control setting arecorrect and there is no steam, gentlytap the soleplate on the ironing board a few times. Movethe variable steam control from "0" to "Max" a fewtimes. • Iron may not be hot enough. Set thermostat to the"Max" position. Always allow iron sufficient time toheat up (thermostat light goes off) before activating the variable steam control. • Overuse of steam burst. Allow more time betweeneach burst. • Iron may have been overfilled. Turn iron off,emptywater and follow instructions for filling. • Steam performance be low if iron requires seasoning. To season, use regular tap water for 1or 2 tanks until steam improves. 2 1. Do not rest iron on soleplate. 2. Never use or rest iron on an unstable surface. 3. While the iron is hot, never set iron on an unprotected surface - even if it is on its heel rest. 4. WARNING! TO PREVENT ELECTRIC SHOCK OR OTHER INJURY, before filling the iron with water, make sure that the plug is removed from the outlet. 5. CAUTION: Never fill the iron with fabric conditioner, starches or any other solution, as these will damage the steam mechanism. Do not use contaminated water. 6. WARNING! TO AVOID FIRE, never leave iron unattended while it is plugged in. 7. WARNING! TO PREVENT ELECTRIC SHOCK, never immerse the iron in water or other liquid. 8. WARNING! TO PREVENT ELECTRIC SHOCK, never use the iron in a location where it can fall or be pulled into water or any other liquid. If the iron falls into water or any other liquid, unplug it immediately. DO NOT reach into the water or liquid. 9. CAUTION: Never use scouring pads, abrasive or chemical cleaners, or solvents to clean the exterior or soleplate of your iron. Doing so will scratch and/ or damage the surface. 10. WARNING! DO NOT aim iron at face, towards yourself, or anyone else while using or adjusting steam. Burns or serious injury may occur. 11. Always store your iron in the upright position, not on the soleplate. If stored face down, even the smallest amount of moisture will cause the soleplate to corrode and stain. 12. DANGER! Never use the iron if it is damaged or dropped. Using the iron when it is damaged could create the risks of fire, electric shock, injury or death. 9 IRONING CHART NOTE: Before starting to iron delicate fabrics, it is best to first test the temperature of the iron on a hem or an inside seam. To select iron temperature, align temperature selected on dial with the indicator on the water tank. ADDITIONAL IMPORTANT SAFEGUARDS DIRECTIONSON LABELFABRICTEMP. CONTROLSTEAMCONTROLBURST OFSTEAMSPRAYPlease note that on the label means ‘THIS ARTICLE CANNOT BE IRONED!” COTTONLINENSYNTHETIC FIBERS, e.g.acrylic, nylonpolyesterSILKWOOLMIN• •• •••MAX0MAXIMUMSTEAMMINIMUMSTEAM GETTING TO KNOW YOUR IRON Before using your 1600 Watt Professional Steam Iron, remove any labels, stickers or tags that may be attached to the body or soleplate of the iron. When turned on for the first time, your new iron may emit an odor for up to 10 minutes. This is due to the initial heating of the materials used in making the iron. 3 The odor is safe and should not reoccur after initial heating. Also, before ironing with steam for the first time, allow iron to heat, hold in a horizontal position and hit the burst of steam button several times. The iron may emit some small particles from the steam holes. This is normal and wil clear after pressing the burst of steam button several times. Technical Specifications Voltage: 120V., 60Hz. Power: 1600 Watts USER MAINTENANCE INSTRUCTIONS EMPTYING THE IRON 1. Always empty iron after each use. 2. When finished using the iron, turn the variable steam control to“0” and the temperature control dial to "MIN". 3. Unplug the iron from the electrical outlet. 4. Set variable steam control to "MAX". 5. Turn the iron upside down over the sink with the tip pointing downward and allow the water to flow from the opening. 6. Set variable steam control to " 0". 7. Allow iron to cool in an upright position before storing. WARNING! Use caution when emptying the iron. Burns may occur from touching hot metal surfaces, hot water or steam. 8 STORAGE 1. Always turn the variable steam control to “0” after you have emptied the water tank. 2. Allow the iron to cool down. 3. Always store the iron in the upright position to protect the soleplate. 4. From time to time...