Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
A firm toothbrush is also ideal for this task. Use care while cleaning because the porcelain is fragile and can crack or break. Do not use water to clean the igniters. If necessary, use a small amount of rubbing alcohol to help dissolve grime. 2. Examine the burner heads. Remove anything stuck in the holes with a straightened paper clip, wire or needle. Be careful not to scratch or damage the ring and head. Do not distort the shape of the burner head holes. Since the burner heads for the SimmerSear™ burners are not removable, they must be cleaned in place. 3. Clean all the burner parts, including the burner bases, with window cleaner or rubbing alcohol. Use a cleaning brush with plastic bristles or a firm tooth brush. When done, rinse the parts well with clean water. Dry all the parts thoroughly before re-assembling them. 4. Reassemble the cooktop according to the burner and grate assembly instructions on page 5. Test the burners after reassembling them. If the flame is uneven, be sure that all the burner parts are properly positioned, then check for any remaining dirt or grime on the burner parts or igniter. If erratic clicking is still present, make sure the igniter is completely dry. If the unit still exhibits problems after drying, call your local Dacor Authorized Service Agent. Cap cover Burner cap Wide side down! Skirt Burner head* Base SimmerSear Burner Assembly Line up notch Cap cover with igniter Burner head IgniterNotch Burner base Standard Burner Assembly Cleaning Stainless Steel Surfaces (stainless steel models only) CAUTION Always wipe stainless steel (silver colored) surfaces with the grain. To prevent scratching, do not use abrasive cleaners or scrubbers on stainless steel surfaces. • Clean stainless steel surfaces with the Dacor Stainless Steel Cleaner included with your cooktop. Use it according to the directions on the package. You may order additional stainless steel cleaner at Order part number A302. • You may also clean the stainless steel surfaces with a mild solution of detergent and warm water. Rinse and dry with a soft, lint-free cloth. Continued... 9 10 Care and Cleaning Cleaning the Knobs and Trim Rings 1. Turn the knobs to the off position to remove the knobs and trim rings for cleaning or replacement. 2. Disconnect the cooktop power plug from the electrical outlet. 3. Grasp each knob and pull straight up to remove. 4. The trim rings may be removed for cleaning if necessary. Take note of the position of each trim ring before removal. Grasp each trim ring and pull straight up to remove. 5. Wash the knobs and trim rings with a solution of warm soapy water. Dacor recommends hand dishwashing liquid. 6. Insert the trim rings into the holes in the positions noted in step 4. Turn the ring until the flame icon is in the 9 o’clock position for each trim ring. 7. To replace the knobs, align the “D-shaped” opening on the bottom of the knob with the end of the valve shaft. Carefully push the knob on until it stops. 8. Connect the cooktop power plug to the electrical outlet. Cleaning the Optional Griddle Clean the griddle after each use. Wash it thoroughly in hot soapy water to avoid stains from grease build-up. The griddle is coated with a non-stick coating for easy cleaning. Warm water and liquid detergent are all that are needed for cleaning. Remove stubborn spots with a non-abrasive plastic mesh pad. To prevent scratching, do not use abrasives or abrasive cleaners. Use the soft side of a sponge to scrub it. Dry it with a lint-free cloth. Replacing the Grate Feet The rubber feet on the bottom of the grate supports can be replaced if they are lost or damaged to prevent damage to the spill tray. If necessary, you may use a pair of needle nose pliers to pull the feet free from the grate. Dacor Part Number Description 103712 Grate support foot (4 used per grate) 103475 12” Grate (2 used per cooktop) 103476 10” Grate (model RGC365 only, 1 used per cooktop) To order parts, contact your Dacor dealer or visit Flame icon in 9 o’clock position Valve shaft Trim ring Knob Before You Call for Service Problem Solution Guide Problem May Be Caused By What to Do Nothing works. Cooktop not connected to electrical power. Check to make sure power cord is connected to electrical outlet. Power to electrical outlet is off. Turn on power at circuit breaker or fuse box. Check for tripped breaker or blown fuse. Power outage. Contact power company. Igniters do not spark. Power not supplied to unit. See Nothing Works above. Wet or dirty igniter. Clean and dry igniter and burner assembly according to Care and Cleaning section. No flame. Igniter not working (no clicking sound). See Igniters do not spark above. Wet or dirty igniter. Clean and dry according to Care and Cleaning section. Gas is turned off. Make sure the gas supply valve is in the on position. Gas supply interrupted. Contact gas company. Burner goes out at low setting. Low gas pressure. Contact gas company ...
Otros modelos de este manual:Placas - PREFERENCE RGC365 (2.32 mb)