Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
This appliance is equipped with a 3-prong grounding Avoid fire hazard or electrical plug for your protection against shock hazard and should be shock. DO NOT use an adapter plug, an extension plugged directly into a properly grounded receptacle. DO NOT cut or cord, or remove grounding prong from electrical remove the grounding prong from this plug. power cord. Failure to follow this warning can cause serious injury, fire or death. Conversion to Liquefied Petroleum Gas (or L.P. Gas) Personal injury or death from electrical This natural gas range is designed to allow for conversion to Liquefied Petroleum (L.P.) Gas. If L.P. conversion is needed, contact the service center for assistance. The L.P. Conversion Kit is provided with this cooktop and is located in the literature envelope. Before installing the kit be sure to follow the L.P. Installation Instructions carefully. shock may occur if the range is not installed by a qualified installer or electrician. Any additions, changes or conversions required in order for this appliance to satisfactorily meet the application needs must be made by an authorized Service Center. 5 6 Assembly of the Surface Burner Heads, Burner Caps and Burner Grates It is very important to make sure that all of the Surface Burner Heads, Surface Burner Caps and Surface Burner Grates are installed correctly and at the correct locations. 1. Be sure to follow the Installation Instructions before installing and using your new cooktop. 2. Remove all packing tape from cooktop. Remove Burner Caps and Burner Heads (See Figure 3). 3. Discard all packing material located under all Burner Heads (if applicable). 4. To replace Burner Heads & Caps, match the letters located under center of Burner Caps with the letters located inside Burner Head (See Figure 3). Place all Burner Heads & Caps on the cooktop while carefully aligning the Electrodes into slots or holes of the Burner Heads (Figure 1). Note: The Burner Heads should sit flat on Cooktop Burner Skirts. 5. Unpack Burner Grates. NOTE: Do not force End Burner Grates down on cooktop. Be careful to line up the 2 Grate Pins located on each of the 2 End Burner Grates into the Pilot holes located on top of the Burner Caps (See Figure 2). Position Burner Grates on cooktop and check that all the Burner Grate legs lie on the glass surface. REMEMBER — DO NOT ALLOW SPILLS, FOOD, CLEANING AGENTS OR ANY OTHER MATERIAL TO ENTER THE GAS ORIFICE HOLDER OPENING. Always keep the Burner Caps and Burner Heads in place whenever the surface burners are in use. Before Setting Surface Controls Grate Pin Burner Cap Pilot hole Electrodes must align into slot or hole for each Burner Head. Figure 4 Figure 5 Figure 3 Figure 3 Figure 2 Figure 1 (Cleaning Chart) Cleaning Various Parts of Your Cooktop Before cleaning any part of the cooktop, be sure all controls are turned OFF and the cooktop is COOL. REMOVE SPILLOVERS AND HEAVY SOILING AS SOON AS POSSIBLE. REGULAR CLEANING WILL REDUCE THE NUMBER OF MAJOR CLEANING LATER. Surfaces How to Clean Glass, Painted and Plastic Control Knobs, Body Pieces, and Decorative Trim Using a soft cloth, clean with mild dish detergent and water or a 50/50 solution of vinegar and water. Follow by rinsing the area with clean water; dry and polish with a soft cloth. Glass cleaners may be used if sprayed on a soft cloth first. DO NOT spray liquids directly on the control pad and display area. Do not use large amounts of water on the control panel - excess water on the control area may cause damage to the appliance. Do not use other liquid cleaners, abrasive cleaners, scouring pads, or some paper towels they will damage the finish. Control Panel Wipe the control panel clean after each use. Before cleaning the control panel, turn all controls to OFF and remove the control knobs.To remove, pull each knob straight off the shaft. Clean using hot, soapy water and a cloth. Be sure to squeeze excess water from the cloth before wiping the panel; especially when wiping around the controls. Excess water in or around the controls may cause damage to the appliance. To replace knobs after cleaning, line up the flat sides of both the knob and the shaft; then push the knob into place. Porcelain Enamel Burner Grates, Burner Rings (some models), Cooktop Surface (some models) Gentle scouring with a soapy scouring pad will remove most spots. Rinse with a 1:1 solution of clear water and ammonia. If necessary, cover difficult spots with an ammonia- soaked paper towel for 30 to 40 minutes. Rinse with clean water and a damp cloth, and then scrub with a soap-filled scouring pad. Rinse and wipe dry with a clean cloth or paper towel. Remove all cleaners or the porcelain may become damaged during future heating. DO NOT use spray oven cleaners on the cooktop. Surface Burners The holes in the burners of your cooktop must be kept clean at all times for proper ignition and a complete, even flame. Clean the burner holes routinely with a small gauge wire or needle and especially afte...