Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Do not use rough abrasive material or sharp metal scrapers as these could scratch the surface and cause the glass to crack. ! The accessories can be washed like averyday crockery (even in your dishwasher). ! Switch off the electricity supply and allow to cool before cleaning the cooker. ! Clean the cooker regularly and wipe up spills soon after they occur to prevent them from becoming burnt on. Never use biological washing powder, caustic cleaners, harsh abrasives, scouring pads, steam cleaners, aerosol cleaners or oven chemical cleaners of any kind. ! To move the cooker forward, open the top oven/grill door and with both hands positioned under the roof of the compartment, lift and pull forward. Replace by pushing the cooker backwards. ! Check that the cooker is level. Take care not to damage any floor coverings. REPLACEMENT OF OVEN LIGHT BULB CAUTION: DISCONNECT THE APPLIANCE FROM THE ELECTRICITY SUPPLY BEFORE REPLACING THE LAMP TO AVOID THE POSSIBILITY OF AN ELECTRIC SHOCK. Light bulbs are not covered by the manufacturer's guarantee. A new 25W, 300°C rated SES bulb can be obtained from your cooker supplier or any major electrical retailer. 1. Remove the shelves from the oven. 2. Unscrew the lens using a thick cloth to protect your fingers in the unlikely event of a lens fracture. 3. Unscrew bulb. 4. Fit new bulb and refit lens. ! If it is necessary to remove the cooker for cleaning, ensure that it is cool and beware that it is heavy (approximately 70 kg 155 lbs). COOKER FINISH CLEANING METHOD Vitreous Enamel Door inner panels, pan supports, burner caps, roasting dish, grill pan, main oven base, inside of grill compartment. Cloth wrung out in warm soapy water. Stubborn stains can be removed with a cream paste, liquid cleaner or by rubbing with fine steel wool soap pads. Check that the cleaning agent is approved by the Vitreous Enamel Association. Paint Side panels. Wash with a cloth wrung out in warm soapy water only. DO NOT USE ABRASIVES. Aluminium Hotplate burner bodies, lid rear trim. Similar to paint cleaning above. Use a nylon brush to remove any cleaning materials, water or dirt from the hotplate burner bodies. Glass As for enamel cleaning. Polish with a clean dry cloth or kitchen roll. Chromium Plating Oven shelves, grill pan grid, grill pan handle support. Wipe with a cloth wrung out in warm soapy water. A fine steel wool soap pad e.g. Brillo, Ajax, or a chrome or stainless steel cleaner may be used. Plastic Grill pan handle, control knobs. Wipe with a cloth wrung out in warm soapy water. Stainless Steel Hotplate, control panel. Wipe with a cloth wrung out in warm soapy water. Polish with a clean dry cloth or kitchen towel. For stubborn stains, use a proprietary stainless steel cleaner and follow the instructions on the container. 14 Something Wrong with your Cooker 0 inDesiT Before contacting your Service Centre or Installer, check the problem guide below, there may be nothing wrong with your cooker. PROBLEM CHECK Burner will not light: Hotplate burner: If all burners fail to ignite: Check that sparks appear at the burners; a clicking noise should be heard. If not; Check that the electricity supply is turned on. If the electricity supply has failed, all burners can be lit by a match. If only one burner fails to ignite: Check that the burner is dry and that spillage of food or cleaning fluid remains are not affecting the ignitor or burner ports. Clean away any debris with a dry nylon brush such as an old toothbrush. If a wire wool pad has been used for cleaning around the burner ensure the ignitor is free from any stray strands. Any water on the burner should be dried with a cloth or kitchen towel. Burner ports Ignitor On the hotplate make sure that all the burner parts are correctly seated. Slight odour or small amount of smoke when grill / oven used first time. This is normal and should cease after a short period. Oven cooks too fast or too slow. Check that the gas mark and shelf positions are as recommended in the Oven Cooking Charts. However, it may be necessary to increase or decrease the recommended setting slightly to suit your taste. Oven lamp does not work. The oven lamp is not covered by the guarantee. The part is easily changed (see the section on oven lamp replacement). A new lamp may be obtained from our Parts department, (see back page). 15 Installation Prior to installation, ensure that the local distribution conditions (nature of the gas and gas pressure) and the adjustment conditions are compatible. The adjustment conditions for this appliance are stated on the data badge which is fitted on the back panel. This appliance is not designed to be connected to a combustion products evacuation device. It must be installed and connected in accordance with current installation regulations. particular attention should be given to the relevant requirements regarding ventilation. MODEL NUMBERS KD6G25SAIR, D6G25SXIR, KD6G25SWIR Category II2H3...
Otros modelos de este manual:Placas - KD6G25SAIR (238.58 kb)
Placas - KD6G25SWIR (238.58 kb)