Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
It can destroy the nonstick coating. Stainless steel or aluminium appliances Clean the oven door with a wet sponge only. Dry it with a soft cloth. Do not use steel wool, acids or abrasive materials as they can damage the oven surface. Clean the oven control panel with the same precautions. CATALYTIC WALLS AND ROOF The walls and the roof with catalytic coating are self-cleaning. They absorb fat Removing the shelf supports which collects on walls while the oven operates. To support this self-cleaning process, heat the oven without any food regularly: • Turn the oven light on. • Remove accessories from the oven. • Select an oven function. • Set the oven temperature to 250 °C and let the oven operate for 1 hour. • Clean the oven cavity with a soft and damp sponge. WARNING! Do not attempt to clean the catalytic surface with oven sprays, abrasive cleaners, soap or other cleaning agents. This will damage the catalytic surface. Discolouration of the catalytic surface has no effect on the catalytic properties. SHELF SUPPORTS You can remove the shelf supports to clean the side walls. 1. Pull the front of the shelf support away from the side wall. ENGLISH 33 2. Pull the rear end of the shelf support away from the side wall and remove it. 21 Installing the shelf supports Install the shelf supports in the opposite sequence. Valid with telescopic runners: The retaining pins on the telescopic shelf runners must point to the front! CAUTION! Make sure that the longer fixing wire is in the front. The ends of the two wires must point to the rear. Incorrect installation can cause damage to the enamel. CLEANING THE TOP OVEN GLASS PANELS The door glass on your product can be different in type and shape from what you see in diagrams. The number of glasses can be different. WARNING! Make sure that the glass panels are cool before you clean the glass door. There is a risk that the glass could break. WARNING! When the door glass panels are damaged or have scratches, the glass becomes weak and can break. To prevent this, you must replace them. For more instructions, contact your local Service Centre. 12 Removing the glass: 1. Open the door. 2. Push the door trim at both sides to release the clips. Refer to the picture. 3. Pull the door trim to the front to remove it. 4. Remove the glass panels. To install panels, do the above steps in the opposite sequence. 34 MAIN OVEN CLEANING THE DOOR GLASS PANELS The door glass on your product can be different in type and shape from the example you see in the diagram. The number of glasses can also be different. Removing the glass: 12A 1. Push the door trim at one side to remove it. Refer to the diagram. 2. Pull up the trim. 3. Remove the glass panels. To replace the glass panels, do the above steps in the opposite sequence. Before you lower the trim, attach the A trim part to the door. Refer to the diagram. OVEN LAMP WARNING! Be careful when you change the oven lamp. There is a risk of electrical shock. Before you change the oven lamp: • Deactivate the oven. • Remove the fuses in the fuse box or deactivate the circuit breaker. Put a cloth on the bottom of the oven to prevent damage to the oven light and glass cover. Replacing the oven lamp 1. You can find the lamp glass cover at the back of the cavity. Turn the lamp glass cover counterclockwise to remove it. 2. Clean the glass cover. 3. Replace the oven lamp with an applicable 300°C heat-resistant oven lamp. Use the same oven lamp type. 4. Install the glass cover. ENGLISH 35 WHAT TO DO IF… WARNING! Refer to "Safety information" chapter. Problem Possible cause Remedy The appliance does not operate The fuse in the fuse box is released Control the fuse. If the fuse is released more than one time, refer to a qualified electrician. The appliance does not operate The power plug is not correctly put in Put in the power plug correctly The appliance does not operate The earth fault switch is switched off Switch on the earth fault switch The appliance does not operate The Child Lock or Key Lock is on Refer to "Lock the control panel" The appliance does not operate The appliance is not activated Activate the appliance The appliance does not operate The clock is not set Set the clock The appliance does not operate The "Automatic cut-out" is on Refer to “Automatic cutout” The food boils or fries too The cookware is not cor-Use correct cookware slowly rect for the heat conductivity with good heat conductivity The signal clock does not work The time is not set Set a time The oven does not heat up The necessary settings are not set Control the settings The oven lamp does not operate The oven lamp is defective Replace the oven lamp The display shows an error code that is not in this There is an electronic fault • Deactivate the appliance with the house list fuse or the safety switch in the fuse box and activate it again • If the display shows the error code again, refer to the Customer Care Department Sound is heard from the cooker after you deactiva...
Otros modelos de este manual:Placas - EN COOKER 49332I-MN (1.73 mb)
Placas - 49332I-MN (1.73 mb)
Placas - EN COOKER 49332I-MN (1.73 mb)
Placas - EN COOKER 49332I-MN (1.73 mb)