Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
Tips for saving energy ¦ Always use a correctly fitting lid for the pan.Cooking without the lid requires four times as much energy. A glass lid allows you to observe the cooking without having to lift the lid off. ¦ Use pots and pans with level bases. Using cookware with unlevel bases increases energy consumption. ¦ The diameter of the base of your pot or pan should match the size of the hotplate. In particular, if pots that are too small are placed on a hotplate, energy is wasted. Please note: Cookware manufacturers often specify the diameter of the top of the pan. This is usually bigger than the diameter of the base of the pan. ¦ Use a small pan for small quantities of food. A large saucepan containing little food requires more energy. ¦ Use only a little water when cooking. This will save energy. It also preserves vitamins and minerals in vegetables. ¦ Switch to a lower heat setting as soon as possible. ¦ Use the residual heat of the hob. For longer cooking times, you can switch the hotplate off as early as 5 - 10 minutes before the end of the cooking time. Getting to know your appliance The instruction manual is the same for various different hobs. An overview of the models with their dimensions is given on page 2. The control panel Controls When you touch a symbol, the respective function is activated. The hotplates ! " "#" # "# "!" $"" $" . Notes ¦ Always keep the controls dry. They are adversely affected by moisture. ¦ Bending or striking the metal panel, e. g. by knocking a pot against it, may cause a malfunction. Hotplate Activating and deactivating $ Single- circuit hotplate . Dual- circuit hotplate Touch the . symbol a Dual- circuit hotplate, hotplate Touch the . symbol; the 2nd filament circuit is activated with extended cooking zone Touch the c symbol; the extended cooking zone is activated When the hotplate is activated: the corresponding display lights up. When the hotplate is switched on: the last selected size is automatically selected again Residual heat indicator If • appears in the display the hob is still hot. It may be used, for example, to keep a small meal warm or to melt cooking The hob has a two-stage residual heat indicator for each chocolate. As the hotplate cools down further, the display hotplate. changes to oe. The display remains lit until the hotplate has cooled sufficiently. Setting discs You can set the heat settings and the timer by turning the setting discs. You can remove the setting discs. This makes cleaning easier. You can also remove the setting discs when the hotplate is in operation. The hotplates switch off after 3 seconds. The residual heat indicator H/h appears in the display. If you refit the setting disc during operation, you can make new settings. Always place the setting disc in the recess with the high-gloss side facing down. Storing setting discs The setting discs are magnetic. Keep the setting discs away from magnetic data media, such as video cassettes, diskettes, credit cards or cards with magnetic strips. The data these contain could otherwise be wiped. They can also cause interference in television sets and monitors. : For wearers of electronic implants, e. g. pacemakers or insulin pumps.! Implants could be affected by magnetic fields. You must therefore never carry the setting discs in your pockets. They must be kept at least 10 cm from pacemakers. Note: The setting discs are magnetic. Small metal parts which attach themselves to the underside can scratch the surface of the glass ceramic and front moulding. Always wipe and clean the setting discs thoroughly. Setting the hob This section informs you how to set the hotplates. The table shows heat settings and cooking times for various meals. Switching the hob on and off The main switch is used to switch the hob on and off. To switch on: touch the # symbol. A signal sounds. The ‹ hotplate indicators light up. The hob is ready for use. To switch off: touch the # symbol until the ‹ hotplate indicators go out. All hotplates are switched off. The residual heat indicator remains on until the hotplates have cooled down sufficiently. Note: The hob switches off automatically if all hotplates have been switched off for more than 10 seconds. Setting a hotplate Use the setting discs to set the desired heat setting. Heat setting 1 = lowest setting Heat setting 9 = highest setting There is an intermediate setting between each heat setting. This is identified by a dot. To set the heat setting: The hob must be switched on. Select the hotplate. Turn the appropriate setting disc until the heat setting indicator shows the desired heat setting. The hotplate is switched on. To change the heat setting: Use the setting disc to set the new heat setting. To switch off the hotplate: Use the setting disc to adjust the setting to ‹ . After about 10 seconds, the residual heat indicator appears. Note: Hotplate temperature is regulated by the heat switching on and off. The he...
Otros modelos de este manual:Placas - ET885DC11D/02 (1.9 mb)
Placas - ET885DC11D/03 (1.9 mb)