Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
Touch the + or - symbol until the desired time appears on the timer display. The time counts down. An audible signal sounds once the time has elapsed. ‹‹ lights up in the timer display for 10 seconds. Displaying the time Use the 0 symbol to select the kitchen timer. The time is displayed for 10 seconds. Changing the time Use the 0 symbol to select the kitchen timer and reset the time. Automatic time limit If a hotplate has been switched on for a long time without the Switch off the hotplate. setting being changed, the automatic time limit is activated. When the time limit is activated depends on the heat setting The hotplate stops heating. ” ‰ and the • / oe residual heat selected ( 1 to 10 hours) . indicator flash alternately on the hotplate display. Note: You can switch the hotplate back on again at any time. Basic settings Your appliance has various basic settings. You can adapt these settings to your own preferences. Display Function ™ ‚ Automatic childproof lock ‹ Switched off. * ‚ Switched on. ™ . Audible signal ‹ Confirmation signal and operation error signal are switched off. ‚ Only the operation error signal is switched on. . Only the confirmation signal is switched on. „ Confirmation signal and operation error signal switched on. * ™ † Automatic timer ‹ Switched off. * ‚ - SS Cooking time, after which the hotplates switch off ™ ‡ Duration of the timer end signal ‚ 10 seconds. * . n 30 seconds „ 1 minute. ™ . Activation of the filament circuits ‹ Switched off. ‚ Switched on. . Last setting before the hotplate was switched off. * ™ ‹ Reset to basic setting ‹ Switched off. * ‚ Switched on. * Basic setting Changing the basic settings 3. Touch the D symbol repeatedly until the desired indicator appears in the left-hand display. The hob must be switched off. 4. Touch the + or - symbol repeatedly until the desired setting 1. Switch on the front left hotplate at heat setting 1. appears in the display. 2. Within the next 10 seconds, press and hold the D symbol for 4 seconds ™ and ‚ flash alternately in the left-hand display; ‹ lights up in the right- hand display. 5. Touch and hold the D symbol for 4 seconds. The setting is activated. 6. Switch off the hotplate. Cleaning and care The information in this section provides help on how best to care for your hob. Suitable maintenance and cleaning products can be purchased from the after-sales service or in our e-Shop. Ceramic Clean the hob after each use. This will prevent spills from burning onto the ceramic. Only clean the hob when it has cooled down sufficiently. Use only cleaning agents which are suitable for glass ceramic. Follow the cleaning instructions on the packaging. Never use: ¦ Undiluted washing- up liquid ¦ Detergent intended for dishwashers ¦ Scouring agents ¦ Harsh cleaning agents such as oven spray or stain remover ¦ Abrasive sponges ¦ High-pressure cleaners or steam jet cleaners Ground-in dirt can be best removed with a glass scraper, available from retailers. Please note the manufacturer's instructions. You can also obtain a suitable glass scraper from our after- sales service or from the e- Shop. Using special sponges to clean glass ceramic achieves great cleaning results. Hob surround To prevent damage to the hob surround, observe the following instructions: ¦ Use only hot soapy water. ¦ Wash new sponge cloths thoroughly before use. ¦ Do not use any sharp or abrasive agents. ¦ Do not use the glass scraper. Rectifying faults Faults often have simple explanations. Please read the following notes before calling the aftersales service. Display Fault Measure Blank There is no power supply. Check the household fuse for the appliance. Check whether there is a power cut by trying other electronic appliances. All displays The controls are damp or an object is Dry the controls or remove the object. flash resting on them. ‹ flashes The controls are damp or an object is Dry the controls or remove the object. Switch off the appliance. Switch the when resting on them. appliance back on. switched on ” ‹ Display faulty. Switch the appliance off and back on again after about 30 seconds using either the household fuse or the circuit breaker in the fuse box. Contact the after-sales service if this appears on the display again. ” . The electronics have overheated and Wait until the electronics have cooled down sufficiently. Then touch a con- have switched off the corresponding trol for the hotplate. hotplate. ” … The electronics have overheated and Wait until the electronics have cooled down sufficiently. Then touch any have switched off all hotplates. control. ” ‰ The hotplate was in operation for too You can switch the hotplate back on again immediately. long and has switched itself off. After-sales service Our after- sales service is there for you if your appliance should need to be repaired. We are committed fo find the best solution also in order to avoid an unnecessary call- out. E number and FD number: Please quote the E number (product number) and the ...
Otros modelos de este manual:Placas - NKN645B17/01 (1.21 mb)