Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
Only use your appliance for the preparation of food and never for room-heating purposes. This appliance leaves the factory set for the gas supply indicated on the data label. Call the Service Centre if it needs to be altered. Do not tamper inside the appliance. If necessary, call your local Service Centre. Overheated fat or oil can easily catch fire. Never leave the appliance unattended when cooking food with fat or oil, e.g. chips. Never pour water on burning fat or oil. DANGER OF BURNS! Cover the receptacle to smother the flames and turn the cooktop off. In the event of a fault, cut the gas and electricity supplies to the appliance. Call our Service Centre to repair the fault. Do not use unstable or uneven-based receptacles on cooking plates or burners. They may accidentally tip over. If a gas supply knob/valve jams, do not force it. Call your official Service Centre immediately for them to repair or replace it. The illustrations used in this booklet are only intended as a guide. Grids become very hot during use. When operating the appliance control knobs, take care not to make contact with the grids. Do not use this appliance neither in marine craft nor in caravans. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Make sure you keep these instructions for use and assembly in a safe place, so that you can hand them on with the appliance if it ever changes owner. Note: To avoid jeopardising the electrical safety of the appliance, it is forbidden to use high-pressure or steam jet cleaning devices. SHOULD THE RELEVANT CONDITIONS NOT BE PROPERLY SATISFIED, THE INSTALLER, AND NOT THE MANUFACTURER, SHALL HELD LIABLE. Installation This installation must conform with the following: Statutory O Manufacturer’s Installation instructions requirements O Local Gas Fitting Regulations O Municipal Building Codes, O Refer to AS/NZS 5601.1 for Gas Installations. O S.A.A. Wiring Code O Local Electrical Regulations O Any other statutory regulations Refer to AS/NZS 5601.1 for piping size details. These Preparing to install built-in cooktops are intended to be inserted in a benchtop cutout. Only an officially authorised technician should connect the appliance. Before you begin, turn off the gas and electricity supply. Installation dimensions are shown in Fig.1. Fig. 1 Clearances Before connecting the unit, check whether the local connection conditions (type of gas) are compatible with the unit’s setting. Observe any special conditions imposed by local suppliers (utilities). The specifications of this cooktop are stated on the data label located on the bottom of the cooktop base. A duplicate data label is supplied for adhesion to an accessible location near the hotplate if the data label on the base of the hotplate cannot be accessed when the hotplate is installed. A range hood fitted above the top must be installed according to the installation instructions for the range hood. A minimum distance of 650 mm is required for a range hood and 750 mm for an exhaust fan. Any adjoining wall surface situated within 200 mm from the edge of any hob burner must be a suitable noncombustible material for a height of 150 mm for the entire length of the hob. Any combustible construction above the hotplate must be at least 650 mm above the top of the burner and no construction shall be within 450 mm above the top of the burner. A minimum depth of 50 mm from the top of the worktop surface must be provided for the appliance. If the base of the hotplate can be touched, a protecting shield must be fitted. This shield must be at least 10 mm from the lowest part of the hotplate and must be capable of withstanding the appliance temperatures. Minimum thickness of benchtop is 30 mm. See Fig. 2. O The shield material must be mdf or similar with minimum thickness of 12 mm. O The shield overall dimensions must be 560 mm wide x 480 mm deep. O Provide cut-out in right hand rear of shield of 80 mm wide x 80 mm deep to provide for gas regulator / LP connection fitting. After installation of the shield the clearance around the top and sides of shield will allow adequate ventilation. Ensure the side and top clearances are not obstructed. . Fig. 2 Installation of cooktop into the kitchen bench If an oven is positioned below the cooktop the barrier does not need to be fitted, but a space of 35 mm must be maintained between the underside of the cooktop and the top of the oven. A space of 5 mm must be maintained between the benchtop and the top front part of the oven. See Fig. 2. Installation procedure: Side clearances: If the distance measured from the periphery of the nearest burner to any vertical surface is less than 200 mm, the surface shall be protected in accordance with clauses 6.10.1.2 of AS/NZS 5601.1 1. For cutout d...