Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
Changing or cancelling the time Press the 0 symbol. Change the time by pressing the 0 to 9 symbols or + and - symbols. To cancel the time, programme it to 0 with the 0 to 9 symbols or with the + and - symbols. Note: When the ° symbol is pressed and the time has not been set, an alert will appear on the display. Automatic time limitation If the hotplate remains in use for a long time and no changes The indicator goes out when any symbol is pressed. The are made in the settings, the automatic time limitation function hotplate can now be reset. is triggered. When the automatic time function is used, it is governed by the The hotplate stops heating. F8 and the residual heat selected power level ( from 1 to 10 hours) . indicator qH/ ph flash alternately on the hotplate display. Cleaning lock Cleaning the control panel while the hob is on may change the settings. In order to avoid this, the hob has a cleaning lock function. Press the >D symbol. An alert will appear on the display. The control panel is locked for 20 seconds. The surface of the control panel can now be cleaned without risk of changing the settings. Note: The lock does not affect the main switch. The hob may be switched off when desired. Settings The device has several basic settings. These settings can be changed. Indicator Function Language English* German French Dutch Italian Portuguese Spanish Danish Swedish Norwegian Finnish Russian Polish Turkish Greek Power levels S ‚. * Beep On* Off Power limit from 1000 W to 9500 W. Childproof lock Increasing the setting increases the power of the hob by 500 W. Manual* Automatic Off. Brightness The brightness of the display can be adjusted. Clock The time can be set Timer On* : To activate the timer press the 0 sensor once. To activate the automatic shut- off of a hotplate, press the 0 symbol twice. Off: The automatic shut- off of a hotplate is activated by pressing the 0 once. Timer end signal Duration of the beep of the time program function: 10 sec* 30 sec 60 sec Basic settings Yes No* *Basic settings Saving some settings takes time. The Ysymbol will appear on the display. Changing the settings The hob should be turned off. 1. Turn on the hob with the main switch. 2. Within the next 10 seconds, press the ° symbol for 4seconds. The first setting will appear between square brackets on the display. 3. Press the + and - symbols until the indicator for the required function appears. 4. Move to the next line with the navigation sensor X. 5. Select the required value using the + and - symbols. 6. Press the ° symbol again for 4 seconds. The settings will have been correctly saved. Exiting the function without saving the settings To exit the settings, switch off the hob at the main switch and select the required settings again. Care and cleaning The advice and warnings contained in this section aim to guide you in cleaning and maintaining the hob, so that it is kept in the best possible condition Hob Cleaning Clean the hob after each use. This prevents food remains left on the surface from burning. Wait until the hob is cold enough before attempting to clean it. Only use cleaning products specifically designed for glass- ceramic hobs. Follow the instructions provided on the packaging. Do not use: ¦ Abrasive products ¦ heavy-duty cleaners, like oven sprays and stain removers ¦ Pads that may scratch ¦ High- pressure or steam cleaners Glass scraper Remove dried-on food remains using a glass scraper. 1. Release the scraper safety catch 2. Use the blade to clean the hob surface Do not attempt to clean the hob surface with the base of the scraper. This could result in scratching. a= Risk of injury! ! The blade is extremely sharp. Risk of cuts. Protect the blade when not in use. Replace the blade immediately when any imperfections are found. Care of the appliance Apply an additive to protect and preserve the hob. Follow the advice and warnings provided with the product. Hob frame In order to avoid damage to the hob frame, follow the indications below: ¦ Use only slightly soapy hot water ¦ Do not use sharp or abrasive products ¦ Do not use a glass scraper Fixing malfunctions Malfunctions are usually due to small details. Before calling the Technical Assistance Service, you should consider the following advice and warnings. Indicator Malfunction Solution none The electric power supply has been cut Use other electrical appliances to check whether there has been a off. power cut. The appliance has not been correctly con- Check that the appliance has been connected correctly according to nected following the connection diagram. the connection diagram. Electronic system malfunction. If in the above checks, the malfunction is not resolved, contact the Technical Assistance Service. Data memory There is an internal error in the operation. Notify the Technical Assistance Service. error ` See user manual “ flashes The control panel is damp or an object is Dry the control panel area or remove the object. restin...
Otros modelos de este manual:Placas - PID975L24E/20 (1.42 mb)