Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
The hotplate stops heating. ” and ‰ flash alternately in the When the time limit is activated depends on the heat setting hotplate indicator. selected (1 to 10 hours) . Basic settings Your appliance has various basic settings. You can adapt these settings to your needs. Indicator Function ™ ‚ Automatic childproof lock ‹ Switched off. * ‚ Switched on. ™ . Audible signal ‹ Confirmation signal and operation error signal switched off. ‚ Only operation error signal switched on. . Confirmation signal and operation error signal switched on.* ™ † Automatic timer ‹ Switched off. * ‚ - SS Cooking time, after which the hotplates switch off ™ ‡ Duration of the timer end signal ‚ 10 seconds. . n30 seconds „ 1 minute. * ™ . Activation of the filament circuits ‹ Switched off. * ‚ Switched on. . Last setting before the hotplate was switched off. ™ ‹ Reset to basic setting ‹ Switched off. ‚ Switched on. *Basic setting Changing the basic settings 3. Touch the 3 symbol repeatedly until the desired symbol appears in the timer display. The hob must be switched off. 4. Use the + or - symbol to set the desired value. 1. Switch on the hob. 2. Within the next 10 seconds, touch the 3 symbol for 4seconds. ™‚ appears in the timer display and ‹ in the hotplate display. 5. Touch the 3 symbol for 4 seconds. The setting is activated. Switching off To exit the basic setting, switch off the hob with the main switch and make new settings. Cleaning and care The information in this section provides help on how best to care for your hob. Suitable maintenance and cleaning products can be purchased from the after- sales service or in our e- Shop. Ceramic Clean the hob after each use. This will prevent spills from burning onto the ceramic. Only clean the hob when it has cooled down sufficiently. Use only cleaning agents which are suitable for ceramic. Follow the cleaning instructions on the packaging. Never use: ¦ Undiluted washing-up liquid ¦ Detergent intended for dishwashers ¦ Scouring agents ¦ Harsh cleaning agents such as oven spray or stain remover ¦ Abrasive sponges ¦ High-pressure cleaners or steam jet cleaners Ground- in dirt can be best removed with a glass scraper, available from retailers. Please note the manufacturer's instructions. You can also obtain a suitable glass scraper from our after- sales service or from the e- Shop. Cleaning the control panel Use only warm, soapy water. Do not use harsh or abrasive agents. The glass scraper should not be used for this purpose. The control panel could be damaged. Lemon and vinegar are not suitable for cleaning the control panel. They could create dull areas. Rectifying faults Malfunctions often have simple explanations. Please read the following notes before calling the aftersales service. Display Fault Action Blank There is no power supply. Check the household fuse for the appliance. Check whether there is a power cut by trying other electronic appliances. “ is flash- The metal bar has been bent or struck. Wait a little and then reset. ing “§ + Electronic fault. Switch the appliance off and back on again after about 30 seconds using number either the household fuse or the circuit breaker in the fuse box. Contact the after- sales service if the display appears again. ” . The electronics have overheated and Wait until the electronics have cooled down sufficiently. Then touch a control have switched off the corresponding for the hotplate.* hotplate. ” … The electronics have overheated and Wait until the electronics have cooled down sufficiently. Then touch any con- have switched off all hotplates. trol.* * Do not place hot pans close to or on the control panel Display Fault Action ” ‰ The hotplate was in operation for too long and has switched itself off. You can switch the hotplate back on again immediately. ” S Electronic fault. Switch the appliance off and back on again after about 30 seconds using either the household fuse or the circuit breaker in the fuse box. Contact the after- sales service if the display appears again. * Do not place hot pans close to or on the control panel After- sales service Our after-sales service is there for you if your appliance should need to be repaired. We are committed fo find the best solution also in order to avoid an unnecessary call-out. E number and FD number: Please quote the E number ( product number) and the FD number (production number) of your appliance when contacting the after-sales service. The rating plate bearing these numbers can be found on the appliance certificate. Please note that a visit from an after- sales service engineer is not free of charge, even during the warranty period. Please find the contact data of all countries in the enclosed customer service list. To book an engineer visit and product advice GB 0844 8928989 Calls from a BT landline will be charged at up to 3 pence per minute. A call set- up fee of up to 6 pence may apply. IE 01450 2655 Trust the expertise of the manufacturer, and rest assured that the repair will be car...