Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
Do not tamper inside the appliance. If necessary, call your local Service Centre. Overheated fat or oil can easily catch fire. Never leave the appliance unattended when cooking food with fat or oil, e.g. chips. Never pour water on burning fat or oil. DANGER OF BURNS! Cover the receptacle to smother the flames and turn the cooktop off. In the event of a fault, cut the gas and electricity supplies to the appliance. Call our Service Centre to repair the fault. Do not use unstable or uneven-based receptacles on cooking plates or burners. They may accidentally tip over. If a gas supply knob/valve jams, do not force it. Call your official Service Centre immediately for them to repair or replace it. The illustrations used in this booklet are only intended as a guide. Grids become very hot during use. When operating the appliance control knobs, take care not to make contact with the grids. Do not use this appliance neither in marine craft nor in caravans. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Make sure you keep these instructions for use and assembly in a safe place, so that you can hand them on with the appliance if it ever changes owner. Note: To avoid jeopardising the electrical safety of the appliance, it is forbidden to use high-pressure or steam jet cleaning devices. SHOULD THE RELEVANT CONDITIONS NOT BE PROPERLY SATISFIED, THE INSTALLER, AND NOT THE MANUFACTURER, SHALL HELD LIABLE. Installation Statutory This installation must conform with the following: O Manufacturer’s Installation instructions requirements O Local Gas Fitting Regulations O Municipal Building Codes, O Refer to AS/NZS 5601.1 for Gas Installations. O S.A.A. Wiring Code O Local Electrical Regulations O Any other statutory regulations Preparing to install Refer to AS/NZS 5601.1 for piping size details. These built-in cooktops are intended to be inserted in a benchtop cutout. Only an officially authorised technician should connect the appliance. Before you begin, turn off the gas and electricity supply. Installation dimensions are shown in Fig.1. Fig. 1 Before connecting the unit, check whether the local connection conditions (type of gas) are compatible with the unit’s setting. Observe any special conditions imposed by local suppliers (utilities). The specifications of this cooktop are stated on the data label located on the bottom of the cooktop base. A duplicate data label is supplied for adhesion to an accessible location near the hotplate if the data label on the base of the hotplate cannot be accessed when the hotplate is installed. A range hood fitted above the top must be installed Clearances according to the installation instructions for the range hood. A minimum distance of 650 mm is required for a range hood and 750 mm for an exhaust fan. Any adjoining wall surface situated within 200 mm from the edge of any hob burner must be a suitable noncombustible material for a height of 150 mm for the entire length of the hob. Any combustible construction above the hotplate must be at least 650 mm above the top of the burner and no construction shall be within 450 mm above the top of the burner. A minimum depth of 50 mm from the top of the worktop surface must be provided for the appliance. If the base of the hotplate can be touched, a protecting shield must be fitted. This shield must be at least 10 mm from the lowest part of the hotplate and must be capable of withstanding the appliance temperatures. Minimum thickness of benchtop is 30 mm. See Fig. 2. Fig. 2 If an oven is positioned below the cooktop the barrier does not need to be fitted, but a space of 35 mm must be maintained between the underside of the cooktop and the top of the oven. Installation of cooktop into the kitchen bench Installation procedure: Side clearances: If the distance measured from the periphery of the nearest burner to any vertical surface is less than 200 mm, the surface shall be protected in accordance with clause 6.10.1.2 of AS/NZS 5601.1 1. For cutout dimensions and clearances refer Fig.1. 2. The clips and the adhesive seal (underside of the cooktop) are already fitted (depending on the model), do not under any circumstances remove them. The seal ensures that the entire work surface will be watertight, and prevents water seepage. In order to fit the appliance into the kitchen unit, first place the cooktop in the correct position then loosen each of the clips so that they all turn freely (it is not necessary to completely undo them). Insert and centre the cooktop. Press the sides of the cooktop until it is supported around its entire perimeter. Turn the clips and tighten them fully. Fig. 3. Fig. 3. Connection Electrical Fig. 4 An electrical 10 amp socket needs to be within 1 m of the hotplate to allow electrical co...
Otros modelos de este manual:Placas - T29R66N0AU/03 (2.27 mb)
Placas - T29R66N0AU/20 (2.27 mb)