Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
We recommend you read the whole book before you start using your cooktop, for the sake of safety as well as success. First use Check that the cooktop is plugged in and the electricity switched on for the electronic ignition to work. Jet 9 (CG902 series) 1. Semi-rapid burner 2. Rapid burner 3. Fish burner 4. Wok burner 5. Auxiliary burner 6. Cooktop controls Titan (CG913 series) Jet 6 (CG602 series) 1 1 1 5 4 4 3 5 2 2 6 6 1 1 4 5 6 2 TITAN MODELS (CG913 Series) Temperature control 1 Choose the control knob for the burner you want to use. 2 Press down gently and turn the knob anticlockwise to the high position. You do not need to hold the knob down. 3 All electrodes will spark until the selected burner ignites. Note: For the first burner selected there is a short delay before the safety valve allows gas to flow to the cooktop. 4 Adjust the flame anywhere between the High and the Low positions. Do not adjust the flame between High and Off. If the cooktop does not light Check that the cooktop is plugged in and the power is switched on. Check that the gas is turned on. Check that the burner parts, including the burner cap, are positioned correctly. High Low Off Burner ON light Correct assembly Incorrect assembly Electrode Burner ring Burner cap Allow two seconds for the safety valve to open when igniting the first burner. A dirty or wet electrode will prevent the burner lighting efficiently. Clean electrodes with a toothbrush and methylated spirits. Electrode Flame failure reignition system In the event of the flame being accidentally blown out, the flame failure reignition system will detect this, and the electrode will spark and relight the flame. If no flame is detected after about five seconds, the gas supply to the appliance will be shut off and the burner ‘ON’ indicator light will flash slowly. The burner must be turned OFF and restarted to resume cooking. Power failure In the event of a power failure, the gas supply will be cut off, even if a burner is in use. When the power is restored and if the burner control knob is still in the ON position, the burner ‘ON’ light will flash rapidly. The burner must be turned OFF and restarted to resume cooking. Accessories Using a wok The pan support over the central ‘wok’ burner is shaped to fit a wok. Care should be taken when using a large wok that other pots are not pushed sideways and become unstable or deflect heat onto nearby walls. Re-assembling the wok burner (CG913TM Iridium models only) Parts of your wok burner have locating pins to help you to assemble it correctly after cleaning. Incorrect assembly can cause irregular flames and ignition problems. Refer to this diagram for the correct order of assembly. Note: The brass parts of your wok burner will change colour with use. This is normal and will not affect performance. Rotate burner ring to align locator pin with hole in burner base. Side view TITAN MODELS (CG913 Series) Inner cap Burner cover (small holes) Decorative ring Burner ring with locator pins (large holes) Align and insert pin 4 Repositioning the pan supports The wok support goes in the centre over the wok burner. The other two pan supports are interchangeable but need to be rotated to match the rounded corners of the hob top. TITAN MODELS (CG913 Series) Using the Simmermat The Simmermat helps you control the temperature of your cooking surface to ensure the long slow simmering that is needed for successfully cooking delicate foods. Use at low heat only. Always remember it is for simmering and exposure to extreme heat may distort it. To use the Simmermat 1 First cook the food, or bring to the boil, over high heat. 2 Then reduce the heat and carefully place the Simmermat over the flame with the points facing upwards. Put your saucepan on top of the points and simmer on the low flame setting. WARNING! Hot Surface Hazard Always turn the burner off before moving the Simmermat and handle the hot Simmermat with tongs and/or pot holders Failure to do so could result in burns and scalds. Rounded corners Correct pan support orientation 5 JET MODELS (CG602 & CG902 Series) Temperature control 1 Choose the control knob for the burner you want to use. 2 Press down gently and turn the knob anticlockwise to the high position. All electrodes will spark until you release the knob. Hold down the knob for approximately five seconds as releasing it too soon may extinguish the flame. 3 Adjust the flame anywhere between the High and Low positions. Do not adjust the flame between High and Off. If the cooktop does not light Check that the cooktop is plugged in and the power is switched on. Check that the gas is turned on. Check that the burner parts, including the burner cap, are positioned correctly. If the burner has not lit within 15 seconds, turn the control knob off and wait at least one minute before trying again. A dirty or wet electrode will prevent the burner lighting efficiently. Clean electrodes with a toothbrush and methylated spirits. High Low Off Correct...