Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
.. The cooking time begins to elapse. Notes ¦ The same cooking time can be set automatically for all hotplates. The set time for each of the hotplates counts down independently. The Basic settings section contains information on automatically programming the cooking time. ¦ If the combi zone or move function is selected when the hotplates are combined, the set time is the same for both hotplates. Changing or cancelling the time Select the hotplate and then press the 0 symbol. Change the cooking time using the programming zone or set to ‹‹ in order to cancel the time. Once the time has elapsed The hotplate switches off. A warning signal sounds. The time program function lights up ‹‹ for 10 seconds in the display. When the 0 symbol is pressed, the indications turn off and the beeping stops. Notes ¦ To program a cooking time of less than 10 minutes, always press 0 before selecting the desired value. ¦ If cooking times have been programmed for various zones, the time program function always displays the time of the selected hotplate. ¦ Cooking times can be programmed for up to 99 minutes. The timer The timer can be set for periods of up to 99 minutes. It is independent of the other settings. This function does not automatically switch off a hotplate. How to program 1. Press the 0 symbol until the U indicator lights up. ‹‹ lights up in the time program function display. 2. Adjust the desired time in the programming zone. The time starts to count down again after a few seconds. Changing or cancelling the time Press the 0 symbol and the U indicator lights up. Change the cooking time in the programming zone or press 0 to cancel the time. Once the time has elapsed Once the time has elapsed, a beep will sound. ‹‹ and Uare displayed in the time program function display. After pressing the 0 symbol, the indications turn off. Cleaning lock function Cleaning the control panel while the hob is switched on may locked for 35 seconds. The control panel surface can now be change the settings. cleaned without the risk of changing the settings. In order to avoid this, the hob has a cleaning lock function. Note: The lock does not affect the main switch. The hob mayPress the > symbol. A signal sounds. The control panel is be turned off when desired. Automatic time limitation If the hotplate remains in use for a long time and no changes are made in the settings, the automatic time limitation function is triggered. The hotplate stops heating. The ”, ‰ symbol and the residual heat indicator oe/• flash alternately in the display. The indicator goes out when any symbol is pressed. The hotplate can now be reset. When the automatic time function is used, it is governed by the selected power level (from 1 to 10 hours). Displaying energy consumption This function displays total energy consumption for the time the The Basic Settings chapter provides information on activating hob has been switched on. this function. After switching off the hob, the consumption in kWh is displayed for 10 seconds. An example is shown in the image with a consumption of ‚.‹‰ kWh. ................ Basic settings The device has several basic settings. These settings may be adapted to the user's individual needs. Indicator Function ™‚ Childproof lock ‹ Deactivated.* ‚ Activated. ™. Audible signals ‹ Confirmation and error signals deactivated. ‚ Only error signal activated. . Only confirmation signal activated. „ All signals activated.* ™„ Display energy consumption ‹ Deactivated.* ‚ Activated. ™† Automatic programming of cooking time. ‹ Switched off.* ‚-SS Automatic shut-off time. ™‡ Duration of the time program function warning signal ‚ 10 seconds*. . 30 seconds. „ 1 minute. ™. Power-Management function ‹ = Deactivated.* ‚ = 1,000 W. minimum power. ‚= 1,500 W. . = 2,000 W. etc. S or S. = maximum power of the hob. ™S Hotplate time selection ‹ Unlimited: the last hotplate programmed remains selected.* ‚ Limited: The hotplate will only remain selected for 10 seconds. *Factory settings Indicator Function ™‹ Return to basic settings ‹ Personal settings.* ‚ Return to factory settings. *Factory settings Accessing the basic settings 3. Touch the 0 symbol repeatedly until the required function is displayed. The hob must be switched off. 4. Then select the required setting from the settings range. 1. Switch on the hob using the main switch. 2. Within the next 10 seconds, touch the 0 symbol for 4 seconds. ™ and ‚ flash alternately in the heat setting display and ‹ appears in the timer display as a preset. 5. Touch the 0 symbol for at least 4 seconds. The settings have been saved. Leaving the basic settings Turn off the hob with the main switch. Care and cleaning The advice and warnings contained in this section aim to guide you in cleaning and maintaining the hob, so that it is kept in the best possible condition Hob Cleaning Clean the hob after each use. This prevents food remains left on the surface from burning. Wait until the hob is cool enough before attempting to clea...
Otros modelos de este manual:Placas - PIS631F17E/01 (545.33 kb)
Placas - PIS651F17E/01 (545.33 kb)