Votos - 4, Puntuación media: 3.5
(
)
)
|
Resumen del manual
Wireless WVC54G (EU/UK) Internet Video Camera Connect the Camera to a Wired Network for Setup NOTE: If you want to connect the Camera to a wireless network for setup, refer to the User Guide on the Setup CD-ROM for instructions. A Attach the antenna. B Connect the included Ethernet network cable to your router, switch, or computer. C Connect the other end of the cable to the Ethernet port on the Camera. IMPORTANT: You MUST connect the Camera to a router, switch, or PC* using an Ethernet network cable BEFORE powering on the Camera. Otherwise, the C Camera will not function. D Connect the included power adapter to the Power port on the Camera. E Plug the power adapter into an electrical outlet. The Ready LED flashes while the Camera is initializing. When the Camera is ready for setup, the Ready and Ethernet LEDs are solidly lit. D * If connecting the Camera directly to a PC, Linksys recommends that you use an IP address of 192.168.1.x (x can be any number from 1-254, but cannot be the same as another device on your network). 2 Set up the Video Camera A Insert the Setup CD-ROM into your CD-ROM drive. The Setup Wizard should run automatically, and the Welcome screen should appear. If it does not, click Start and then Run. In the field provided, enter D:\wvc54g.exe (if “D” is the letter of your CDROM drive). B Click Setup to begin the setup process. C Make sure the Camera is properly connected to your network. Click Next. D The screen will display a list of Wireless-G Internet Video Cameras on your network and status information. In the Selection box, click the name of the Camera you are currently installing. Click Next. EA verify password screen will appear. In lowercase letters, enter admin in the Administrator Name and Password fields. Click OK. D E A C F Enter a unique name for the Camera in the Camera Name field, and complete the Description field. Select your time zone, and enter the date and time. Then click Next. G If your network has a router or other DHCP server, select Automatic Configuration- DHCP. If the Camera requires a static IP address, keep the default setting, Static IP address. Click Next. H If you selected Automatic Configuration-DHCP in step G, then proceed to step I. If you selected Static IP address, the IP Settings screen will appear. Enter an IP Address, Subnet Mask, and Default Gateway appropriate for your network. You must specify an IP Address and Subnet Mask. If you are unsure about the Default Gateway, then leave this field blank. Complete the Primary DNS and/or Secondary DNS fields. Enter at least one DNS address, which you can obtain from your ISP. Click Next. NOTE: The default IP address of the Camera is 192.168.1.115. F G H NOTE: If your LAN IP address is different than 192.168.1.x, you may get an error message when you configure the camera through your PC. Ignore the error message. A After you clicked the Install Viewer & Recorder Utility button, the Welcome screen will appear. Click Next. B To install the Utility files in the default folder, click Next. To select a different folder, click Browse and follow the on- screen directions. C To add program icons to the default folder, click Next. To add program icons to an existing folder, select one from the Existing Folders listed, and then click Next. D When the ActiveX plug-in has been installed, you will see the screen shown in Figure D. Then click OK. E When the setup is complete, click OK. F To open the Utility, double-click its shortcut on your desktop. 3NOTE: On the Congratulations screen of the Setup Wizard, you can click the Setup SoloLink DDNS Service button to take advantage of the Camera’s Dynamic Domain Name System (DDNS) feature. This is useful for remote access of the Camera via the Internet. Refer to the SoloLink™ Quick Installation for more information. A After you clicked the Install Viewer & Recorder Utility button, the Welcome screen will appear. Click Next. B To install the Utility files in the default folder, click Next. To select a different folder, click Browse and follow the on- screen directions. C To add program icons to the default folder, click Next. To add program icons to an existing folder, select one from the Existing Folders listed, and then click Next. D When the ActiveX plug-in has been installed, you will see the screen shown in Figure D. Then click OK. E When the setup is complete, click OK. F To open the Utility, double-click its shortcut on your desktop. 3NOTE: On the Congratulations screen of the Setup Wizard, you can click the Setup SoloLink DDNS Service button to take advantage of the Camera’s Dynamic Domain Name System (DDNS) feature. This is useful for remote access of the Camera via the Internet. Refer to the SoloLink™ Quick Installation for more information. 4 Connect the Video Camera for Install the Viewer & Recorder Utility Wireless Network Use Click the Infrastructure radio button if you want the Camera to communicate using an access point or wireless router. Click the Ad-Hoc radio...