Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Your SpeedZone Sport bicycle computer is equipped with the following functions: • SPD - Current Speed • AV – Average Speed • MAX – Maximum Speed • DST - Trip Distance • OD - Odometer (total distance) • TM – Ride Timer • 12/24 Hour Digital Clock • Easy Calibration Mode This computer also features: • Heavy-duty abrasion resistant pick-up wire • Water resistant housing • Dual Display LCD • 2 Year Warranty What is included in your SpeedZone Sport package: 1. SpeedZone Sport computer (1) 2. Mounting bracket (1) 3. Magnet with screw (1) 4. Cable tie wraps (4) 5. Mounting bracket sizing straps (3) 1 2 3 5 4 FIGURE 1: FIGURE 2: SENSOR MAGNET PLACEMENT ATTACHMENT MOUNTING THE SPEEDZONE SPORT The SpeedZone Sport sensor can mount on the right or left side of the fork blade. Use the cable tie-wraps provided to position the sensor. Do not tighten until the final placement of the sensor magnet is correct. (See figure 1) FIGURE 3: MOUNTING BRACKET Attach the magnet to a spoke across from the sensor with the magnet screw. The clearance between the magnet and the sensor should be approximately 1/32"-1/16" (1-2mm). Tighten the magnet and transmitter. Do not overtighten the magnet screw. (See figure 2) Attach the mount to the handlebar using the bracket screw provided. Tighten so that the bracket cannot rotate on the handlebar. There are several sizing straps provided to fit different diameter bars. (See figure 3) Slide the computer forward onto the mounting until it ‘snaps’ into place with an audible click. To remove the computer, push it backward until it releases from the mount. To test for proper installation of the magnet, sensor and computer, activate the computer by picking up the front of the bicycle and spinning the wheel. The "wheel" (1) indicator will flash. If it does not flash check the sensor and magnet alignment. Realign as necessary until the "wheel" indicator flashes while spinning the wheel. PROGRAMMING Programming the functions of your SpeedZone Sport requires it to be placed in various "modes" (i.e. odometer mode, stopwatch mode). The computer can be cycled through these modes by pressing the "MODE" button located on the right-hand side of the housing. Once a specific mode has been entered, its values can be reset or adjusted by pressing the "FUNCTION" button located on the left-hand side of the housing. 1. Miles or Kilometers selection Your SpeedZone Sport will record speed and distance in either miles (M) or kilometers (KM). To select miles or kilometers, push the "MODE" button until ODO (odometer) appears in the lower left side of the display (This is called the odometer mode). Hold down the "FUNCTION" (left side) button and ‘tap’ the "MODE" button once. The KM, M indicator will begin blinking. You may now alternate between miles and kilometers by pressing the "MODE" button. When the correct choice is flashing, select it by pressing the "FUNCTION" button. You will now enter the "Programmable Odometer" mode. If the odometer setting is correct push the "FUNCTION" button 4 times to exit to odometer mode. (Otherwise, see "Setting the programmable odometer" below) 2. Setting the Programmable Odometer To access the programmable odometer mode, first advance the "MODE" button until (OD) appears on the bottom of the screen. Then hold down the "FUNCTION" button and ‘tap’ the "MODE" button once. (See figure 4) The Km/h indicator will flash. If the Km/h setting is correct press the FIGURE 4: PROGRAMMABLE ODOMETER SCREEN "FUNCTION" button once and a four- digit number will appear. You are now in the programmable odometer mode. This mode is useful if you have replaced the battery and would like to retain the mileage you have already ridden. To enter a mileage into the odometer, press the "MODE" button until the flashing digit is correct. (Note: The "MODE" button may be held to scroll to the correct digit.) Press the "FUNCTION" button to select the next digit to the right. Repeat this process until all four digits are entered as your existing mileage. 3. Wheel Circumference Selection To set the circumference for the type of tires you are using, you can either use the table below to obtain an approximate tire circumference or measure your actual tire circumference by the rollout method. Easy Calibration Mode: Your SpeedZone Comp has been preprogrammed with the following 14 Specialized tire sizes: 26 X 1.0 26 X 2.2 26 X 1.25 650 X 20 26 X 1.5 700 X 20 26 X1.9 700 X 23 26 X1.95 700 X 26 26 X 2.0 700 X 32 26 X 2.1 700 X 38 When using Easy Calibration Mode, the SpeedZone will display the tire size on its LCD display screen. (See figure 5) The Easy Calibration Mode is accessed by entering the odometer (OD) mode and holding down the "FUNCTION" button for three seconds. The display will now show the currently selected tire size. To scroll through the FIGURE 5: EASY CALIBRATION SCREEN preprogrammed tire sizes tap both the "MODE" and "FUNCTION" buttons simultaneously. When you reach the desired tire size press the "FUNCTION" bu...