Votos - 3, Puntuación media: 5
(
)
)
|
Resumen del manual
To test for proper installation of the magnet, transmitter and computer, activate the computer by pushing the ‘ MODE’ (right side) button. Pick up the front of the bicycle and spin the front wheel. The “ wheel option” indicator will flash. If it does not flash, check the sensor and magnet alignment. Realign as necessary until the “ wheel option” indicator flashes while spinning the wheel OPERATION AND PROGRAMMING When your Turbo ® Comp has not detected any speed input for 30 minutes, it will enter sleep-mode in order to conserve battery power. During sleep mode only the digital clock is displayed. The computer will wake it up when wheel speed is detected or when the MODE or SET button is pressed. In order to operate your computer it must be placed in various “ modes” (i.e. odometer mode, distance mode). The computer can be cycled through these modes by pressing the “ MODE” button located on the right-hand side the MODE/SET rocker switch. There are nine cycling modes available: 1) Clock Mode, 2) Odometer Mode, 3) Trip Distance Mode 4) Average Speed Mode, 5) Maximum Speed Mode, 6) Automatic Timer Mode, 7) Timer/Stopwatch Mode, 8)Interval Mode and 9)Distance Countdown mode. Once you familiarize yourself with the mode operation you will find it very easy to navigate. The following flowchart outlines the mode sequence. Once a particular mode has been entered, its values can be reset or adjusted by pressing and holding the “ SET ” button for three seconds. CLOCK I ODO I TRIP I AVSPD I MXSPD I ATM – I TIMER I INT I Dist• 1. Setting the Display Language Your Turbo ® can display information on the dot-matrix display area in six different languages: English (ENGL), German (GER), French (FR), Italian (ITA), Dutch (NED), and Spanish (ESP). To select your language push the mode button repeatedly until CLOCK is displayed in the Dot-matrix Display Area. Then, depress hold the “ MODE” button for three seconds. The selected language will be displayed. Use the “ MODE” button to scroll through the languages. When the selected language is displayed (default language is English), press the “ SET” button once to confirm your selection and exit display language mode. 2. Miles or Kilometers selection (English only): Your Turbo ® Comp will record distance and speed in either miles (m & m/h) or kilometers (K & Km/h). Please note that miles can only be selected when the language setting is English. All other languages display only kilometers. (See “ Setting the Display Language” above). To enter your selection of miles or kilometers, push the “ MODE” button until ODO appears in the Dot-matrix Display Area (This is called the odometer mode). Next, hold down the “ SET” button for three seconds. The “ Km” or “m” indicator will begin blinking. You may now alternate between miles and kilometers by pressing the “ MODE” button. When the correct choice is flashing, select it by pressing the “ SET” button. You will now enter the “ Programmable Odometer” mode. If the odometer setting is correct push the “ SET” button five times to exit odometer mode. (Otherwise, see “ Setting the programmable odometer” below). 3. Setting the Programmable Odometer: This mode is useful if you have replaced the battery and would like to retain the mileage you have already ridden. To access the Programmable odometer mode, first advance to the Odometer Mode by pressing “ MODE” button until ODO appears in the Dot-matrix Display Area. Hold down the “ SET” button for three seconds (If you have selected English language, the Km/h indicator will flash. If the Km/h setting is correct press the “ SET” button once) and a five-digit number will appear. You are now in the programmable odometer mode. To enter a mileage into the odometer, press the “ MODE” button until the flashing digit is correct. ( Note: The “ MODE” button may be held to quickly scroll to the correct digit.) Press the “ SET” button to select the next digit to the right. Repeat this process until all five digits are entered as your existing mileage. (See figure 7) FIGURE 7 4. Wheel Circumference Selection: To set the circumference for the type of tires you are using, you can use Specialized’s “ Easy Calibration Mode” or measure your actual tire circumference by the rollout method. Two different tire diameters may be entered by using the computer’s “ Second Wheel Option. ” Easy Calibration Mode: Your Turbo ® Comp has been preprogrammed with the following 14 Specialized tire sizes: 26 X 1.0 26 X 2.2 26 X 1.25 650c X 20 26 X 1.5 700c X 20 26 X 1.9 700c X 23 26 X 1.95 700c X 26 26 X 2.0 700c X 32 26 X 2.1 700c X 38 When using Easy Calibration Mode, the Turbo ® Comp will display the tire size on its LCD display screen. (See figure 11) The Easy Calibration Mode is accessed by entering the Odometer (ODO) mode and holding down the “ MODE” button for three seconds. The display will now show the currently selected tire size for wheel option #1. To scroll through the preprogrammed tire sizes press the “ MODE” button. ...