Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
2. Position top of rack parallel to the ground. Check distance from stay mounting hole on Moose Rack to the bicycle’s seat stays. Figure 1 BA Figure 1: The difference between heights A & B must be less than 3/4” (19.05 mm) rACK MuSt Be LeVeL. WheN PuLLiNg A trAiLerCYCLe, A NoN-LeVeL rACK CAN ADVerSeLY AFFeCt BiCYCLe hANDLiNg, reSuLtiNg iN AN ACCiDeNt or SeriouS iNJurY. WArNiNg 3. Adjust rack stays to fit. Photo 1 Moose Rack Instructions Contents: (2) Band Clamps (4) M5 Socket Head Screws (4) Washers (2) Lock Nuts Tools Required: 4mm Hex Key Wrench 5mm Hex Key Wrench Installation Instructions 1. Using washers and socket head screws, attach bottom of rack to holes in bicycle dropouts. 2. Position top of rack parallel to the ground. Check distance from stay mounting hole on Moose Rack to the bicycle’s seat stays. Figure 1 BA Figure 1: The difference between heights A & B must be less than 3/4” (19.05 mm) rACK MuSt Be LeVeL. WheN PuLLiNg A trAiLerCYCLe, A NoN-LeVeL rACK CAN ADVerSeLY AFFeCt BiCYCLe hANDLiNg, reSuLtiNg iN AN ACCiDeNt or SeriouS iNJurY. WArNiNg 3. Adjust rack stays to fit. Photo 1 Rack StayS Photo 1 Rack StayS Photo 1 4. Temporarily attach rack stays to rack and bicycle with washers and socket head screws (Photo 2), or use band clamps to attach rack stays to seat stays (Photo 3). 5. If stays protrude above top of rack, excess length can be trimmed with a hacksaw. Mark stays, then remove stays to cut. 6. Reinstall stays and tighten all nuts. Recommended torque: M6 Nuts: 6-8 N-m (Newton-meter) M5 Screws: 4-5 N-m hArDWAre For AttAChMeNt to BiKeS With threADeD eYeLetS iN reAr DroPout iS ProViDeD. CoNtACt Your AuthoriZeD BurLeY DeALer BeFore AtteMPtiNg to MouNt MooSe rACK oN A BiKe Without threADeD eYeLetS iN the reAr DroPout. iMPortANt Socket Screws Photo 2 Band Clamps Photo 3 Burley Trailer Limited Warranty The Burley Moose Rack is warranted from date of purchase against defects in materials and workmanship under normal use and service. Burley will repair or replace parts it determines to be defective for a period of five years. The Burley owner must present the rack for repair at place of purchase, with an original sales receipt or similar proof of purchase. This warranty applies only to the original owner and is nontransferable. Burley can not be responsible for failure due to improper assembly, modification of parts or instructions, neglect, abuse, accident, and/or normal wear. The warranty does not cover any rack used for rental, competition, or commercial use. Burley neither assumes nor authorizes any person to assume any other liability in connection with this Burley product, and there are no oral agreements or warranties collateral to or affecting this agreement. This warranty gives you specific rights. You may also have other rights which vary by state or country. BURLEY DESIGN Copyright © 2008 by Burley Design LLC. “Burley” is a registered trademark of Burley Design LLC : Rev 09/08 : 170152 Moose Rack Installation Instructions r0 4020 Stewart Rd. Eugene, OR 97402 : PH 541.687.1644 800.423.8445 FAX 541.687.0436 : burley@burley.com : 4. Temporarily attach rack stays to rack and bicycle with washers and socket head screws (Photo 2), or use band clamps to attach rack stays to seat stays (Photo 3). 5. If stays protrude above top of rack, excess length can be trimmed with a hacksaw. Mark stays, then remove stays to cut. 6. Reinstall stays and tighten all nuts. Recommended torque: M6 Nuts: 6-8 N-m (Newton-meter) M5 Screws: 4-5 N-m hArDWAre For AttAChMeNt to BiKeS With threADeD eYeLetS iN reAr DroPout iS ProViDeD. CoNtACt Your AuthoriZeD BurLeY DeALer BeFore AtteMPtiNg to MouNt MooSe rACK oN A BiKe Without threADeD eYeLetS iN the reAr DroPout. iMPortANt Socket Screws Photo 2 Band Clamps Photo 3 Burley Trailer Limited Warranty The Burley Moose Rack is warranted from date of purchase against defects in materials and workmanship under normal use and service. Burley will repair or replace parts it determines to be defective for a period of five years. The Burley owner must present the rack for repair at place of purchase, with an original sales receipt or similar proof of purchase. This warranty applies only to the original owner and is nontransferable. Burley can not be responsible for failure due to improper assembly, modification of parts or instructions, neglect, abuse, accident, and/or normal wear. The warranty does not cover any rack used for rental, competition, or commercial use. Burley neither assumes nor authorizes any person to assume any other liability in connection with this Burley product, and there are no oral agreements or warranties collateral to or affecting this agreement. This warranty gives you specific rights. You may also have other rights which vary by state or country. BURLEY DESIGN Copyright © 2008 by Burley Design LLC. “Burley” is a registered trademark of Burley Design LLC : Rev 09/08 : 170152 Moose Rack Installation Instructions r0 4020 Stewart Rd. Eugene, O...