Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
7. Using two screwdrivers, one inside the bucket and one outside, tighten the mounting screws firmly, until the spring washers are fully flattened between the mounting screw heads and fender washers. 8. Take care to keep the far left post from rotating as you tighten its mounting screw so that the brake return spring does not distort. Flag Handlebar Flag Installation Hole Handlebar Installation Rollbar Accessory (optional) Knob Using the Parking Brake For All Trailers Except the Bee™ Engage the parking brake by pushing the handle to the right. This pushes the brake arms outward so that the tip of each brake engages the inside of each tire. Exercise caution when disengaging the brake, as it may spring to the left. To disengage the brake, move the handle to the RIGHT. Simply move the handle to the LEFT to engage the brake. Installing the Safety Flag Bee™ Only: On the outer left side of the trailer, insert the safety flag pole through the webbing loop and into the flag pocket. All Other Models: Insert the safety flag pole into the hole in the top of the LEFT handle bar receiver. (See handle bar illustration on page 12 for location of correct hole.) DO NOT USE YOUR TRAILER WITHOUT THE SAFETY FLAG. Installing the Cover Bee™: Snap the cover snap buttons to the snap posts on the top of the frame. Attach the cover’s Velcro hook strips to the Velcro loop strips on the trailer body. Then hook the rubber O-rings over the back and front frame ends. To stow the window, unhook the O-rings from the trailer front. Roll the window up and secure it by inserting it into the elastic loops at the top. Cub™: Snap the two front snap buttons to the two snap studs under the front rim corners. Attach the male buckles on the rear cover corners to the female buckles below the side windows. All Other Models: Slip D-rings on the front cover corners over the outer hooked corners of the front tongue receptacles. Attach male buckles on rear cover corners to female buckles below the side windows. To stow the front window (all models except the Bee), unzip it, roll it up and insert the loop Velcro ends of the elastic straps into the hook Velcro holders on the cover top. The Adjustable Sunshade slides up and down as needed. Cover Snap Button Buckle Snap Buttons D-RINGS: d’Lite™ Ladybug™ Solo™ Encore™ Padded Seat & Shoulder Harness, Child Seat Recliner, and Recessed Helmet Pocket (d’Lite™, Solo™, Lady Bug™, Cub™) To Install Seat Pad: Attach the seat pad Velcro hook strips to the loop Velcro strips on the seat. To Install Shoulder Harness Pad: Insert the shoulder straps into the shoulder harness pad as shown in the drawing at the right. The shoulder straps should be oriented so that the FLAT parts of the male buckles are facing toward each other. Using the Child Seat Recliner The child seat can be reclined for added comfort by making the following adjustments: 1. Loosen the tension on the straps (A) attached to the top of the frame. 2. Loosen the tension in the helmet pocket straps (B). Using the Recessed Helmet Pocket (d’Lite™, Solo™, Lady Bug™, Cub™) The helmet pocket, which is designed to provide added room for the back side of a child’s helmet, can be modified by loosening/tightening the helmet pocket straps (B) as required. Using the Child Seat Divider (d’Lite™, Lady Bug™ only) This feature keeps two passengers from sliding to the center of the seat. Connect center crotch strap O-ring to snap hook located on the front splash guard. Adjust strap tension with the plastic slider on the crotch strap. NOTE: Use the Seat Divider feature only when transporting two passengers. Using the Seat Harness Only passengers who are able to wear a helmet and sit upright, unassisted should ride in a child trailer. Adequate neck strength is required by passengers to hold their heads upright while trailering. A physician should evaluate anyone who is of questionable developmental age for trailering. IMPORTANT: Single Passenger, Solo™: 1. Make sure the seat pad and shoulder harness are installed as indicated in the previous section. 2. Position the child in the center of the seat. 3. Snap shoulder straps into the Y-buckle, with the buckle positioned at the child’s sternum. 4. Make sure the shoulder straps are adjusted so that the child cannot move too far forward in the seat. 5. Fasten and adjust the lap belt so that it is snug. Single Passenger, All Other Models: 1. Unclip the center support strap (with O-ring). 2. Remove both shoulder harnesses (if applicable) from the shoulder straps. Unclip the Y-buckle if necessary. Store one of the shoulder harnesses in a safe place. Leave outboard shoulder straps dangling. 3. Remove the two center shoulder straps by unthreading them from the ladder locks. 4. Trade the position of the shoulder straps and re-insert the straps into the ladder locks as shown in the illustration to the right. The flat parts of the male portion of the Y-buckle should face toward the center. 5. Install one shoulder harness assembly in the cente...
Otros modelos de este manual:bicicletas - CUB (1.28 mb)
bicicletas - SOLO (1.28 mb)
bicicletas - BEE (1.28 mb)
bicicletas - d'LITE (1.28 mb)