Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
To set the units 1. Cycle Mode to MAX (Figure 12). 2. HoldSet• KMH or MH flashes. 2 Easy setup (reSet) CLKTMEAVGMAXTRPODOMHMode Set Mode Set 3. Cycle Mode CLKTME ODO MAXTRPAVG MPH F Figure 3- oDo screen MH and KMH interchange on the screen. 4. Push Set• to select. The temperature icon display. 5. Cycle Mode to C or F 6. Push Set• to select. The computer returns to the start screen. To set the odometer 1. Cycle Mode to ODO (Figure 13). 2. HoldSet• 5-digit odometer value appears with first digit flashing. 3. Cycle Mode to your preferred value. 4. Push Set• to select. The next digit flashes. 5. Repeat steps 3 and 4 until all digits are selected. The computer returns to the start screen. Easy setup (reSet) 3 CLKTMEAVGMAXTRPODOMHSet Set Mode To set wheel size Both the 9i and 11i allow you to use two different wheel sizes. The icon for Wheel 1 is a small circle. The icon for Wheel 2 is a partial circle surrounding the Wheel 1 icon (Figure 14). 1. Cycle Mode to TME. 2. HoldSet• Wheel Select icon appears on the screen. 3. Cycle Set• to change wheel selection from Wheel 1 to Wheel 2. 4. Push Modeto select. Wheel size appears. Note: If you want to set a custom wheel size, go to page 24 now. Figure 4- Wheel select screen 5. Cycle Mode The wheel size changes. 6. Hold Set• to select. The computer returns to current speed. To set the second wheel size, repeat the instructions, but select the other Wheel Select icon. 4 Easy setup (reSet) Mode CLKTMEAVGMAXTRPODOMHSet To select the wheel for use 1. 2. Holdthe left Modeand the right Modetogether. Cycle Mode to TRP The Wheel Select icon changes (Figure 14). Repeat step 2 to change again. Easy setup (reSet) 5 CLKTMEAVGMAXTRPODOMHSet Set Mode To set Clock 1. Cycle Mode to CLK (Figure 15). 2. HoldSet• “12” or “24” flashes. 3. Cycle Mode 12 and 24 interchange on the screen. 4. Push Set• to select The clock appears on the screen with the Hour flashing. 5. Cycle Mode The Hour changes. 6. Push Set• to select. The Minutes flash. 7. Cycle Mode 8. Push Set• to select. The computer returns to current speed. CLKTME AVGMAXTRP AVG MPH F Figure 5- CloCK screen 6 Easy setup (reSet) CLKTMEAVGMAXTRPODOMHMode Set Mode Set RESTART gETTINg REAdy TO RIdE Your computer stores data for two intervals- since last ReSet and since last ReStart. ReSet sets ALL data to zero. ReStart sets only the Trip data to zero. The trip modes include • TRP • TME • MAX This operation sets all four values to zero, allowing the computer to display information for a single ride. To ReStart (set the Trip data to zero) 1. Cycle Mode to TRP (Figure 16). 2. Hold Set•, and do not let up until after completing step 3. 3. HoldMode. The Max setting ReStarts at ‘0’. CLKTMEAVGMAXTRPAVG MPH F Figure 6- TrP screen reStart CLKTMEAVGMAXTRPODOMHMode Set Mode Set AddITIONAl INfORMATION Changing mode Once the computer is programmed and installed, it is very easy to use. To change to different modes (functions), simply Cycle the Mode button until the desired function appears, shown by the spelled name of the function. Removing the computer from the computer base The computer is held on its base by a flexible snap. To remove the computer, press firmly on the computer (not on the base) in a rearward direction. using the computer in wet weather Bicycle computers function on electricity. If the electrical contacts between the computer and its base become saturated, the electrical signals may become irregular or interrupted entirely. If the computer is to be used in heavy rain, etc., we recommend that a plastic bag be put over the computer and its base. The other parts of the computer system are waterproof. 8 Additional Information TROuBlEShOOTINg The Incite 9i computer is designed to be easy to install and maintain. However, computers occasionally have problems. Table 3 shows some possible problems, causes, and solutions: Table 3- Common problems and solutions Blank screen Computer is in shipping mode. Push a button. Battery is dead, or installed incorrectly. reinstall good battery. Erratic data Magnet misaligned or too far away. re-adjust magnet and sensor placement. Battery power is low. replace battery. no current speed Magnet misaligned or too far away. re-adjust magnet and sensor placement. Speed is incorrect. Wheel size is incorrect. reset computer. Sensor is not reading magnet properly. readjust magnet and sensor alignment. Troubleshooting 9 REPlACINg ThE BATTERy Figure - removing battery cover If the computer is giving erratic information, the computer or hear rate strap battery may be running low on power (normally accompanied by the low battery icon, Figure 16). Replace the batteries whenever the computer malfunctions, or every 6 months. When purchasing new batteries, it is best to take the old batteries with you. However, this is the generic description for the proper battery: CR2032, lithium cell, 3 volts When the battery is removed, the computer automatically resets function totals to Zero. After installing a new battery, you can ...
Otros modelos de este manual:bicicletas - 11i (604.09 kb)