Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Pat. Nos. 4633216/4636769/4642606/5236759 and Design Pat. Pending Copyright© 2005 CATEYE Co., Ltd. CCVT1W-050113 066600380 2 Component name 1Bracket 2Speed Sensor A 3Magnet 4Bracket Rubber Pad 5Sensor Rubber Pad 6Nylon Ties (L x2) 7Nylon Ties (S x2) 8Double-sided tape CC-VT100W VECTRA Wireless ENG 2 SETTING OPERATION FLOW BATTERY 27 x 1 - 3/8 TIRE 14 x 1.50 14 x 1.75 16 x 1.50 16 x 1.75 18 x 1.50 18 x 1.75 20 x 1.75 20 x 1-3/8 22 x 1-3/8 22 x 1-1/2 24 x 1 24 x 3/4 Tubular 24 x 1-1/8 24 x 1-1/4 24 x 1.75 24 x 2.00 24 x 2.125 26 x 7/8 26 x 1(59) 26 x 1(65) 26 x 1.25 26 x 1-1/8 26 x 1-3/8 26 x 1-1/2 26 x 1.40 26 x 1.50 26 x 1.75 26 x 1.95 26 x 2.00 26 x 2.10 26 x 2.125 26 x 2.35 26 x 3.00 27 x 1 27 x 1-1/8 27 x 1-1/4 27 x 1-3/8 650 x 35A 650 x 38A 650 x 38B 700 x 18C 700 x 19C 700 x 20C 700 x 23C 700 x 25C 700 x 28C 700 x 30C 700 x 32C 700C Tubular 700 x 35C 700 x 38C 700 x 40C Tire size L (cm) ETRTO 47-305 47-406 47-507 23-571 37-590 40-559 47-559 50-559 54-559 57-559 57-559 32-630 18-622 20-622 23-622 25-622 28-622 32-622 37-622 40-522 102 106 119 120 134 135 152 162 177 179 175 178 179 191 189 192 196 192 191 195 195 190 207 210 200 201 202 205 206 207 207 208 217 215 216 216 217 209 212 211 207 208 209 210 211 214 217 216 213 217 218 220 L cm Current Speeed 0.0 (4.0) - 105.9 km/h [0.0 (3.0) - 65.9 mph] MODE MODE MODE MODE MODE MODE MODE MODE Wheel Circumference All Clear PUSH! Select km/h or mph Mx Odo Dst 0 AC a b c ODO Manual Set Clock Setting Wheel Circumference All Clear a COMPUTER CR2032 Open Close SENSOR COIN SET : km/h SET : 10001.0 km TIRE : 27x1-3/8 SET : L = 217 cm START 205 (100 - 299 cm) (100 - 299 cm) 0 - 23 [1 - 12] 24 hr [12 hr] 00 - 59 (00000.0 - 99999.9) START km/h START 00000.0 00001.0 00001.0 10001.0 206 207 217 SETTING END SET AC MODE B A C D SET Open Close E CR2032 2 sec MODE E MODE COIN MODE SET SET SET SET Odo 0-9999.9 10000-99999 km[mile] Mx 0.0(4.0)-105.9 km/h [0.0(3.0)-65.9 mph] RESET RESET Dst 0.00-999.99 km [mile] RESET 0:00-23:59 [1:00-12:59] RESET MODE L cm Dst Mx 2 sec 0 MODE SET SET SET SET SET CAUTION • Do not concentrate on the computer while riding. Be sure to ride safely! • Install the magnet, sensor, and bracket securely. Check these periodically. • Dispose of used batteries according to local regulations. If swallowed, consult a doctor immediately. • Avoid having the computer in hot direct sunlight for extended periods. • Do not disassemble the computer. • Clean the computer and accessories with a soft cloth dampened with a neutral detergent. Do not use thinners, benzene, or alcohol on the computer. Wireless Sensor The sensor was designed to receive signals within a limited range to prevent sensor signal interference. Thus, the sensor and computer must be relatively close. If the temperature or battery power is low, they may need to be even closer than normal. The sensor must be installed at the top of the fork, and the distance between the sensor and the computer should not exceed approximately 70 cm. Install the computer on the stem, with its bottom surface facing the sensor. (Take into account the angle of the stem.) Interference may occur, resulting in malfunction, if thecomputer is: • Near a TV, PC, radio, motor, or in a car or train. • Close to a railroad crossing, railway tracks, TV stations and or radar base. • Close to a second bicycle with wireless sensors. Correct installation of sensor and magnet A Attach the magnet 3 so that it passes through the sensor zone of the sensor 2. B Be sure to have a 5 mm-or-less clearance between the sensor 2 and magnet 3. Part names A B C D Current Speed Sensor signal reception icon Flashes in sync with sensor signals. Speed unit Mode symbol ...................................................... b Indicates the mode currently selected. Mx .............. [Maximum Speed] Odo ............. [Total Distance] Dst .............. [Trip Distance] .............. [Clock] E Battery Case Cover Starting/Stopping measurement This computer automatically starts measurement when the bicycle is moving. Switching Mode symbol ...................... b Press the MODE button to cycle through different functions, which are listed in the OPERATION FLOW chart. Resetting data .................................. b As shown in the OPERATION FLOW, press the MODE button to clear data when RESET appears on the screen. The trip distance cannot be reset. Power-saving function If the computer has not received a signal for 10 minutes, power-saving mode will activate and only the clock will be displayed. When the computer receives a sensor signal again, the measuring screen reappears. If the unit remains inactive for two weeks, the unit enters SLEEP mode. Press the MODE button to stop SLEEP mode. Setting the clock ............................... c With the symbol displayed, press the SET button to set the clock. Press the MODE button to move time forward. The value changes more rapidly if the button is pressed and held. Press the SET button to move from the “hour” ...