Votos - 2, Puntuación media: 5
(
)
)
|
Resumen del manual
If you have heart problems, you are not active, and/or are over the age of 35 years, do not use the pre-set programs or start an exercise program without first contacting and receiving approval from your physician. To avoid the risk of electrical shock, always keep the console dry. Do not spill liquids on the console. Keys Fitness recommends a sealed water bottle for beverages consumed while using the unit. Please review the following drawing below to familiarize yourself with the listed parts. 4 CONSOLE FAN SWITCH FAN TRANSPORT WHEEL POWER CONNECTOR SEAT ADJUSTMENT PULSE HANDLEBARS Assembly Assembly Parts CONSOLE(36) SEAT(45) RAIL TUBE(13) BACKREST(44) UPRIGHT TUBE(35) SEAT CARRIAGE(40) MAIN FRAME(1) REAR STABILIZER(15) PEDALS(33&34) REAR SUPPORT TUBE(47) FRONT STABILIZER(20) CONSOLE TUBE COVER(83) 5 Assembly Assembly Accessories 8*19mm Washer(10)-14 M8*15mm Screw(12) - 14 M8*70mm Carriage Bolt(76) - 2 M8*85mm Carriage Bolt(17) - 2 M8*85mm Carriage Bolt(17) - 2 M8 Cap Nut(19) - 4 M6*40mm Hex Head Screw(48) - 8 6*13mm Washer (49)-8 Iron Plate(51) - 1 M4*8mm Screw(51) - 4 ALLEN WENCH SCREW DRIVER 6 Assembly 7 1. Attach the Front Stabilizer(20) to the Main Frame(1) with two Carriage Bolts(76), two Arc Washers(18), and two Cap Nuts(19). 2. First, attach the Rear Stabilizer(15) to the Rear Support Tube(47) with two Carriage Bolts(17), two Arc Washers(18), and two Cap Nuts(19). Connect the Rail Tube(13) with the Rear Support Tube(47) with four Screws(12) and four Washers(10). Figure 2 Figure 1 INSTRUCTIONS FOR ASSEMBLY: Unpack the box in a clear area. Check to make sure all components are present and in good condition. Do not dispose of the packing material until the assembly is completed. Tools have been provided for you to use when assembling the product. If you need assistance please go to our website at or call 1 888-340-0482. Assembly Figure 3 Figure 4 3. First, thread the Right Pedal(34) into the Right Crank Arm(30). Tighten the pedal securely using the wrench that has been provided. Next, find the Pedal Strap marked “R” and snap one of the 3 hole ends onto the inside of the pedal then snap the other 3 holed end onto the outside of the pedal. Repeat step to install the Left Pedal(33) into Left Crank(29). Note: The Left Pedal(33) is reverse threaded. You will turn the pedal counter clock-wise to thread it into the Left Crank Arm(29). 4. Install Back Cushion(44) onto the Seat Frame(40) with four Hex Head Screws(48) and four Washers(49). Next, install Seat(45) onto the Seat Frame(40) using four Hex Head Screws(48) and four Washers(49). 8 Assembly Figure 6 Figure 5 5. First, Seat Frame(40) onto the Rail Tube(13), pull the Pulse Wires(52) in the Seat Frame(40) and Pulse Wires(53) in the Rail Tube(13) out of the square on the bottom of the Seat Frame(40). Next, connect the Pulse Wires(52) to Pulse Wires(53) as shown in Figure 5. After the pulse wires are connected place them inside the square in the bottom of the Seat Frame(40). Secure the iron plate with four Screws(51). Last, adjust the Seat Frame(40) at the desired position and fix it with the Locking Knob(46). 6. Place the Rail Tube(13) on to the Main Frame(1) and secure in place with four Screws(12) and four Washers(10). 9 Assembly 10 7. First, insert the Console Tube Cover(83) onto the Console Tube(35). Next, connect the Upper Electronic Wire(56) and the Lower Electronic Wire(57). Connect the Pulse Wires(54) to Pulse Wires(55). Last slide the Console Tube(35) onto the Main Frame(1) and secure in place using three Washers(18) and three Screws(12). 8. Plug the Upper Electronic Wire(56) into the back of the Console(36). Then, plug the Pulse Wires(55) with the pulse wires coming from the Console(36). After the wires are connected slide the Console(36) onto the Console Tube(35) and fix in place with four Screws(37). Note: The four Screws(37) will already be installed in the back of the Console(36) when you remove it from the box. Congratulations: You have completed the assembly of your new CardioMax 700r Recumbent bike. Figure 7 INSERT THE AC ADAPTER INTO FRONT LOWER RIGHT HAND SIDE OF BIKE. Exploded View 11 Parts List CM700r RECUMBENT PARTS LIST REF # DESCRIPTION QTY REF # DESCRIPTION QTY 1 MAIN FRAME 1 43 SQUARE TUBE CAP 4 2 FLYWHEEL 1 44 BACK CUSHION 1 3 NUT 3/8" 1 45 SEAT 1 4 WASHER 10*19*1.5mm 1 46 ADJUSTMENT KNOB 1 BC NUT 3/8" 1 47 REAR SUPPORTING TUBE 1 6 SPACER FOR FLYWHEEL 1 48 HEX HEAD BOLT M6*40mm 8 7 BEARING 6000ZZ 3 49 WASHER 6*13*1.0mm 8 8 AXLE FOR FLYWHEEL 1 50 PULSE PLATE 1 9 GREASED BEARING 1 51 SCREW 4 WASHER 8*19*1.5mm 15 52 SENSOR WIRE 2 11 NYLOCK NUT M8 2 53 PULSE WIRE 1 2 12 SCREW M8*15mm 14 54 PULSE WIRE 2 2 13 MOVING TUBE 1 55 PULSE WIRE 3 2 14 REAR SUPPORTING TUBE 1 56 UPPER ELECTRONIC WIRE 1 REAR STABILIZER 1 57 LOWER ELECTRONIC WIRE 1 16 END CAP 2 58 MOTOR WIRE 1 17 CARRIAGE BOLT M8*85mm 2 59 SENSOR WIRE 1 18 ARC WASHER 8*19*1.5mm 4 60 SCREW M4*11mm 1 19 CAP NUT M8 4 61 MOTOR 1 FRONT STABILIZER 1 62 SCREW M4*12mm 4...