Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Before you start, please read the Owner's Manual and become familiar with the operation of your new unit. Remember to take the time to perform the stretching exercises provided to avoid injury. If you are taking medication, consult your physician to see if the medication will affect your exercise heart rate. If you have heart problems, you are not active, and/or are over the age of 35 years, do not use the pre-set programs or start an exercise program without first contacting and receiving approval from your physician. To avoid the risk of electrical shock, always keep the console dry. Do not spill liquids on the console. Keys Fitness recommends a sealed water bottle for beverages consumed while using the unit. Please review the following drawing below to familiarize yourself with the listed parts. 4 CONSOLE FAN SWITCH FAN TRANSPORT WHEEL POWER CONNECTOR SEAT ADJUSTMENTS PULSE HANDLEBARS Assembly 5 MAIN FRAME(1) CONSOLE(67) HANDLEBARS(63) SEAT POST(44) REAR STABILIZER(3) CONSOLE TUBE(40) PEDALS(27&28) SEAT(52) Assembly Parts Assembly Assembly Accessories M8X20mm SCREW(64) - 4 ALLEN WENCH SCREW DRIVER M8X85mm CARRIAGE BOLT(75) - 2 M8X15mm Screw(30) - 4 8x19mm ARC WASHER(5) - 6 8x19mm WASHER(39) - 4 M8 CAP NUT(6)-2 6 Assembly INSTRUCTIONS FOR ASSEMBLY: Unpack the box in a clear area. Check to make sure all components are present and in good condition. Do not dispose of the packing material until the assembly is completed. Tools have been provided for you to use when assembling the product. If you need assistance please go to our website at or call 1 888-340-0482. 7 Figure 1 1. Attach the Rear Stabilizer(3) onto the Main Frame(1) with two Carriage Bolts(75), two Arc Washers(5) and two Cap Nuts(6). 2. First, thread the Right Pedal(27) into the Right Crank Arm(23). Tighten the pedal securely using the wrench that has been provided. Next, find the Pedal Strap marked “R” and snap one of the 3 hole ends onto the inside of the pedal then snap the other 3 holed end onto the outside of the pedal. Repeat step to install the Left Pedal(28) into Left Crank(24). Note: The Left Pedal(29) is reverse threaded. You will turn the pedal counter clockwise to thread it into the Left Crank Arm(24). Figure 2 Assembly Figure 4 Figure 3 3. Bolt the Seat(52) to the Seat Post(44) using four Spring Washers(48), four Washers(49), and four Nylock Nuts(50). 4. Remove Seat Knob(41) from Main Frame(1). Insert Seat Post(44) into the Main Frame(1). Reinsert Seat Knob(41) to tighten the Seat Post(44) down. 8 Assembly Figure 5 Figure 6 5. First, Connect the Upper Electronic Wire(70) to the Lower Electronic Wire(71). Next, slide the Console Tube(40) onto the Main Frame(1) making sure not to cut the wire. Last, secure the Console Tube(40) to the Main Frame(1) using four Washers(5) and four Screws(30). 6. Pull the Upper Electronic Wire(70) through the large hole at the top of the Handlebars(63). Fasten the Handlebars(63) to the Console Tube(40) using four Washers(39) and four Screws(64). 9 Assembly INSERT THE AC ADAPTER INTO LOWER RIGHT HAND SIDE OF THE BIKE. Figure 7 7. First, connect Upper Electronic Wire(70) to the back of the Console(67). Next, clip the Pulse Wires(69) to the two pulse wires coming from the Console(67). Last, secure the Console(67) to the Handlebars(63) using four Screws(68). Note: The four Screws(68) will already be installed in the back of the Console(67) when you remove it from the box. Congratulations: You have completed the assembly of your new CardioMax 700u Upright bike. 10 Exploded View 11 Parts List CM700u UPRIGHT PARTS LIST REF # DESCRIPTION QTY REF # DESCRIPTION QTY 1 MAIN FRAME 1 42 SEAT TUBE SPACER 1 2 FRONT STABILIZER CAP 2 43 BUSHING 1 3 REAR STABILIZER 1 44 SEAT POST 1 4 END CAP 76.2(mm) 2 45 KNOB 1 ARC WASHER 6 46 BOLT M6*10 2 6 CAP NUT M8 2 47 SQUARE TUBE SPACER 2 7 MOTOR 1 48 SPRING WASHER 4 8 BOLT M4*8m 4 49 WASHER 4 9 SENSOR WIRE 1 50 NYLOCK NUT 4 PULLEY 1 51 SEAT RAIL 1 11 MAGNETE 6004ZZ 1 52 SEAT 1 12 BEARING 6004ZZ 2 53 IDLER WHEEL SPRING 1 13 AXLE OF PULLEY 1 54 WASHER 10*26*2.0(mm) 2 14 C CLIP 2 55 HEX HEAD BOLT 3/8"*26 1 BEARING 2 56 NYLOCK NUT 3/8" 1 16 ONE WAY BEARING 1 57 IDLER WHEEL PLATE 1 17 WASHER 20*38*0.5(mm) 1 58 IDLER WHEEL SPACER 1 18 RIGHT COVER 1 59 IDLER WHEEL 1 19 LEFT COVER 1 60 BEARING 6000ZZ 1 LEFT ROUND TRAY 1 61 MAGNETIC PLATE 1 21 RIGHT ROUND TRAY 1 62 NYLOCK NUT 1 22 LITTLE ROUND CAP 2 63 HANDLEBARS 1 23 RIGHT CRANK 1 64 BOLT M8*20 4 24 LEFT CRANK 1 65 FOAM GRIP 2 HEX HEAD BOLT M8*20 2 66 HANDLEBAR CAP 31.8(mm) 2 26 CRANK CAP 2 67 CONSOLE 1 27 RIGHT PEDAL 1 68 CONSOLE SCREWS 4 28 LEFT PEDAL 1 69 PULSE WIRE 2 29 FRONT COVER 1 70 UPPER ELECTRONIC WIRE 1 BOLT M8*15 7 71 LOWER ELECTRONIC WIRE 1 31 BELT 490 J6 1 72 BELLOW 1 32 MAGWHEEL 1 73 WASHER 10*19*1.5(mm) 1 33 GREASED BEARING 1 74 NUT M10 1 34 BEARING 6000ZZ 2 75 CARRIAGE BOLT M8*85 2 AXLE FOR MAGWHEEL 1 76 BOLT M4*30 5 36 FLYWHEEL SPACER 10*13*4mm 1 77 BOLT M4*16 13 37 BC NUT 3/8" 1 78 MOTOR WIRE 1 38 NYLOC...