Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Be sure to read your Owner’s Guide before using your new Fitness Bike. If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12 NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL screws are in place and partially threaded in before completely tightening any ONE screw. A s s e m b l y G u i d e R2600iNetTV COMMERCIAL FITNESS BIKE STEP 6 TOOLS & PARTS INCLUDED 5 5 MM 6MM Allen Wrench Allen Wrench Screwdriver 5MM L-Shaped Wrench 4MM L-Shaped Wrench PARTS BOX Console Mast Cover, Qty: 1 Water Bottle & Cage, Qty: 1 Heart Rate Chest Strap, Qty: 1 Color-coded Hardware Bags Assembly Guide Warranty Card CONSOLE BOX iNetTV Console Owner’s Guide HARDWARE INCLUDED ORANGE BAG GREEN BAG PINK BAG BLUE BAG M8 x 15L Screw Quantity: 7 M8 x 20L Screw Quantity: 2 M8x65L Screw Quantity: 2 M8 Lock Washer Quantity: 4 M8 Lock Washer Quantity: 6 M8 x 20L Screw Quantity: 2 M8 Lock Washer Quantity: 4 BLACK BAG M6 x 55L Screw Quantity: 8 M6 Lock Washer Quantity: 8 M8 x 15L Screw Quantity: 4 M8 Lock Washer Quantity: 8 M8 x 20L Screw Quantity: 4 5 STEP 1 • Install the rear foot with the four lock washers (M8), two inside screws (M8x65L), and two outside screws (M8x20L). Tighten with the 5MM Allen wrench. ORANGE BAG STEP 1 STEP 2 • Slide the rubber boot onto the console mast. • Locate the bundle of wires that comes from the console mast frame bracket. Wrap the wire tie coming from the bottom of the console mast around the bundle of wires. Pull the wire tie with the bundle of wires up through the top of the console mast while simultaneously sliding the mast into the frame bracket. • Secure the console mast to the frame bracket with six lock washers (M8) and six screws (M8x15L). Tighten with the 5MM Allen wrench. Place the seventh screw (M8x15L) in the rear of the frame bracket and tighten until snug. • Slide the console mast boot down and snap it into place on the side cover. • Remove the screws located half way up the console mast with the Phillips screwdriver. Attach the water bottle bracket to the console mast with these two screws. Insert the water bottle. BLUE BAG STEP 2 6 STEP 3 • Mount the upper handlebars to the console mast using two lock washers (M8) and two screws (M8x20L). Tighten with the 5MM Allen wrench. PINK BAG STEP 3 STEP 4 STEP 4 • Remove the six mounting screws from the back of the console. Set the console into place on the console mast and secure it with the six screws you just removed. Tighten with the Phillips screwdriver. Connect the wires to the proper plugs in the back of the console (see diagram). CONSOLE 1 - Co-Axial Cable TV 2 - USB - B 3 - USB - A 4 - VGA (PC Video) 5 - Video IN 6 - Audio - R 7 - Audio - L 8 - Microphone 9 - Heart Rate Reciever 1 10 - Heart Rate Reciever 2 11 - 20 Pin Connector 12 - Power Plug 13 - Miles/Kilometers Switch 14 - Data Port 1 2 3 4 5 6 7 8 14 9 10 11 12 13 WIRES STEP 5 • Attach the seat frame to the sliding seat bracket using four socket head cap screws (M8x20L) and the 6MM Allen wrench. • Connect Wires A on the seat handlebar to Wires B on the sliding seat bracket. Attach the seat handlebars to the sliding seat bracket using four lock washers (M8) and four screws (M8x15L). Tighten with the 5MM Allen wrench. GREEN BAG Wires B Wires A 5STEP • Attach the seat frame to the sliding seat bracket using four socket head cap screws (M8x20L) and the 6MM Allen wrench. • Connect Wires A on the seat handlebar to Wires B on the sliding seat bracket. Attach the seat handlebars to the sliding seat bracket using four lock washers (M8) and four screws (M8x15L). Tighten with the 5MM Allen wrench. GREEN BAG Wires B Wires A 5STEP 7 8 500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551 toll free 1.800.335.4348 • phone 1.920.648.4090 • fax 1.920.648.3373 .2002 Vision Fitness. All Rights Reserved. 8.02 Part #Z26RB60-AG1825PRD AG18.25PRD REV1 STEP 6 STEP 6 • Secure the Lumbar controlled seat back and the seat bottom to the seat frame with eight lock washers (M6) and eight screws (M6x55L). Tighten with the 4MM Allen wrench. • Snap the plastic seat cover into place on the back of the Lumbar controlled seat. BLACK BAG ...