Votos - 4, Puntuación media: 4.8
(
)
)
|
Fotos y especificaciones Vision Fitness R2600HRT |
Resumen del manual
• Unfold the wire harness and heart rate wires located in the console mast frame bracket. Attach the wire tie coming from the bottom of the console mast to the wire harness and heart rate wires. Pull the wire tie with wire harness and heart rate wires up through the top of the console mast while simultaneously sliding the mast into the frame bracket. • Secure the console mast to the frame bracket with six lock washers (M8) and six screws (M8x15L). Tighten with the 5mm Allen wrench. Place the seventh screw (M8x15L) in the rear of the frame bracket and tighten until snug. • Slide the console mast boot down and snap it into place on the side cover. BLUE BAG 1STEP• Install the rear foot with the four lock washers (M8), two inside screws (M8x65L), and two outside screws (M8x20L). Tighten with the 5mm Allen wrench. ORANGE BAG Rear Foot Console Mast Console Mast Boot 2STEP Frame Bracket 5 3STEP• Mount the upper handlebars to the console mast using two lock washers (M8) and two screws (M8x15L). Tighten with the 5mm Allen wrench. • Remove the four mounting screws from the back of the console. Connect the wire harness and heart rate wires that come from the console mast into the plugs located in the back of the console. Make sure the 9-Volt battery is plugged in and in place on the console. Attach the console to the mast with the four screws removed earlier. PINK BAG 3STEP• Mount the upper handlebars to the console mast using two lock washers (M8) and two screws (M8x15L). Tighten with the 5mm Allen wrench. • Remove the four mounting screws from the back of the console. Connect the wire harness and heart rate wires that come from the console mast into the plugs located in the back of the console. Make sure the 9-Volt battery is plugged in and in place on the console. Attach the console to the mast with the four screws removed earlier. PINK BAG 3STEP Console Mast Handlebar 6 4STEP• Attach the seat frame to the sliding seat bracket using four lock washers (M8) and four socket head cap screws (M8x20L) and the 6mm Allen wrench. • Connect Wires A on the seat handlebar to Wires B on the sliding seat bracket. Attach the seat handlebars to the sliding seat bracket using four lock washers (M8) and four screws (M8x15L). Tighten with the 5mm Allen wrench. GREEN BAG • Attach the seat frame to the sliding seat bracket using four lock washers (M8) and four socket head cap screws (M8x20L) and the 6mm Allen wrench. • Connect Wires A on the seat handlebar to Wires B on the sliding seat bracket. Attach the seat handlebars to the sliding seat bracket using four lock washers (M8) and four screws (M8x15L). Tighten with the 5mm Allen wrench. GREEN BAG Seat Handlebar 4STEPWires B Wires A Seat Frame Sliding Seat Bracket 7 5STEP• Secure the Lumbar controlled seat back and the seat bottom to the seat frame with eight lock washers (M6) and eight screws (M6x55L). Tighten with the 4mm Allen wrench. • Snap the plastic seat cover into place on the back of the Lumbar controlled seat. BLACK BAG • Secure the Lumbar controlled seat back and the seat bottom to the seat frame with eight lock washers (M6) and eight screws (M6x55L). Tighten with the 4mm Allen wrench. • Snap the plastic seat cover into place on the back of the Lumbar controlled seat. BLACK BAG Plastic Seat Cover 5STEPLumbar Controlled Seat Back Seat Bottom 8 9 500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551 toll free 1.800.335.4348 • phone 1.920.648.4090 • fax 1.920.648.3373 ©2004 Vision Fitness. All Rights Reserved. 9.04 Part #Z26RB77-AG AG18.30PRD REV2 6STEPAccessory Tray Pedal 6STEP• Attach the left and right pedals to the left and right crank arms. Tighten the pedals using the 15mm Pedal Wrench. • Secure the Accessory Tray to the seat handlebar with two screws (M5x35L) and two lock washers (M5). Tighten with the screwdriver. YELLOW BAG 9 500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551 toll free 1.800.335.4348 • phone 1.920.648.4090 • fax 1.920.648.3373 ©2004 Vision Fitness. All Rights Reserved. 9.04 Part #Z26RB77-AG AG18.30PRD REV2 6STEPAccessory Tray Pedal 6STEP• Attach the left and right pedals to the left and right crank arms. Tighten the pedals using the 15mm Pedal Wrench. • Secure the Accessory Tray to the seat handlebar with two screws (M5x35L) and two lock washers (M5). Tighten with the screwdriver. YELLOW BAG ...