Votos - 5, Puntuación media: 4
(
)
)
|
Resumen del manual
Homeowner: Keep Installation Instructions for future reference. Save Installation Instructions for local electrical inspector's use. Quick Reference Table of Contents: Pages Before you start Electrical requirements Product dimensions Vent system requirements Installation steps Customized front panel Use and Care Information Accessories 2 3 3 4 5-7 7-8 8-9 9 Part No. 4329226/4360365 Rev. C Before you start... Your safety and the safety of others is very important. We have provided many important safety messages in this manual and on your appliance. Always read and Your safety and the safety of others is very important. We have provided many important safety messages in this manual and on your appliance. Always read and This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” obey all safety messages. or “WARNING”. These words mean: DANGER You can be killed or seriously injured if you don’t immediately follow Proper installation is your responsibility. • Have a qualified technician install the range hood. • Comply with installation clearances specified on the model/serial rating plate. Model/serial rating plate is located behind the left filter on rear wall of the vent hood. Range hood location should be away from strong draft areas, such as windows, doors and strong heating vents. Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance. Consult your cooktop/range manufacturer installation instructions before making any cutouts. Grounded electrical outlet is required. See “Electrical requirements.” Important: Observe all governing codes and ordinances. You can be killed or seriously injured if you don’t follow instructions. WARNING All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. instructions. This vent hood is factory set for venting through the roof or wall. For non-vented (recirculating) installations, non-vented (recirculating) kit, Part No. 883140 is available from your dealer or authorized parts distributor. WARNING — TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable Codes and Standards, including Fire Rated Construction. The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society of Heating Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. Ducted fans must always be vented to the outdoors. WARNING — To reduce the risk of fire, use only metal ductwork. This unit must be grounded. Tools needed: pliers pencil drill 1-1/4" drill bit level wire stripper or utility knife 3/8" (8mm) nut driver or ratchet gloves measuring tape Parts supplied for installation: • 2 screws • damper • plastic cover (used for customized front panel) Parts needed for installation: • wood filler strips for cabinets with recessed bottoms (step 5, page 5) • 2,1" x 1" x 5" (25.4 x 25.4 x 127 mm) wood pieces – optional (step 10, page 6) • 2, 1/2" (12.7 mm) U.L.- or C.S.A.-listed conduit connectors • 1 wall cap for interior-mounted motor • metal vent system • 4, 1-1/4" (31.8 mm) wood screws • power supply cable Phillips screwdriver flat-blade screwdriver caulking gun and weatherproof caulking compound duct tape metal snips saber or keyhole saw safety glasses Electrical requirements Important: Observe all governing codes and ordinances. It is the customer’s responsibility: •To contact a qualified electrical installer. •To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 — latest edition*, or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 - latest edition** and all local codes and ordinances. If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate. Do not ground to a gas pipe. Check with a qualified electrician if you are not sure downdraft vent is properly grounded. Do not have a fuse in the neutral or ground circuit. IMPORTANT: Save Installation instructions for electrical inspector’s use. A.A 120-volt, 60-Hz, AC-only, 15-ampere fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit serving only this appliance be provided. B.THE VENT HOOD MUST BE CONNECTED WITH ...