Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Attach the bracket, with ground wire and ridges down, to the ceiling fixture outlet box with the mounting hardware included with the outlet RIDGE box. SIDE Tighten the screws firmly by hand only, being careful not to CEILING DOWN WIRING bend the bracket by over tightening. CAUTION: To reduce the risk of CROSSBAR personal injury, use only the MOUNTING mounting hardware provided with BRACKET the approved outlet box to install the crossbar mounting bracket. APPROVED OUTLET BOX HARDWARE GREEN GROUND FLAT WIRE WASHER CANOPY HARDWARE CANOPY SCREW (4) CANOPY HATCH CANOPY CANOPY LOCK WASHER (4) 4 BELLA™ BELLA™ CANOPY INSTALLATION CANOPY LOCK WASHERS CANOPY SCREWS CROSSBAR MOUNTING BRACKET INSTALLED CANOPY Note: On sloped ceilings, align the canopy opening towards the top or room peak. Step 2. Attach the canopy to the crossbar mount- ing bracket with three of the 8-32 x 21/4. long canopy screws and canopy lock washers. Tighten the screw firmly by hand only. HANGING THE FAN Step 3. To hang the fan body in the canopy, hold the fan body firmly and insert the ball into the canopy opening. Check that no wires were pinched. Rotate the fan body until the slot in the ball fits into the pin opposite the canopy opening. NOTE: The fan weight is 30 pounds. BALL SLOT PIN CANOPY ELECTRICAL CONNECTIONS Step 4. Attach the fan wires to the ceiling fixture outlet box wiring by twisting the bare ends of the wires together and then securing with a wire nut. Connect in this order: • GREEN leads from mounting plate and fan to GROUND conductor of power source. Secure with wire nut. • WHITE wire from fan to white NEUTRAL wire in ceiling fixture outlet box. Secure with wire nut. • BLACK wire from fan to black (or red) POWER wire in ceiling fixture outlet box. Secure with wire nut. (2) WHITE WIRES (2) WIRE NUT GREEN WIRES (3) BLACK WIRES 5 CANOPY HATCH INSTALLATION Step 5. Tuck the wires into the canopy with the wire nuts pointed upwards, so that the WHITE and BLACK wires are on opposite sides of the canopy and all wires are clear of the canopy opening. Step 6. Install canopy hatch with the last canopy screw and lock washer. To do this, HATCH tilt the fan body away from the hatch opening. LAST Tighten the screws firmly by hand only, LOCK WASHER Step 7. Straighten the fan, then check to ensure that there is no movement between the canopy and ceiling or Hang-Tru ball and top support shaft. TILT THE FAN TO INSTALL CANOPY SCREW CANOPY CANOPY SCREW BLADE & BLADE HOLDER HARDWARE BLADE SCREW BLADE BLADE (4 PER BLADE) BADGE HOLDER BLADE HOLDER SCREW (2 PER BLADE) BLADE BADGE INSTALLATION Step 8. Attach the blades to the blade holders by first pressing the blade badge into the blade, then installing the blade holder using the four blade screws and flat washers provided for each blade. Using the screwdriver, tighten securely by hand only. Repeat for each blade assembly. BLADE BLADE SCREW HOLDER (4 PER BLADE) BLADE BLADE BADGE 6 6 Step 9. Remove the blade access plate next to the light fixture. Set aside the two screws and the plate—they will be reinstalled later. BLADE ACCESS PLATE REMOVAL BLADE ACCESS PLATE LIGHT FIXTURE BELLA™ INSTALL BLADES Step 10. Using the blade holder screws from the pack, attach each blade/blade holder assembly to the motor (two screws per blade). Use the blade access hole to install the screws. Using the screwdriver, tighten securely by hand only. BLADE HOLDER SCREW BLADE ACCESS PLATE INSTALLATION Step 11. Using the two screws removed in Step 9, reinstall the blade access plate to the fan as shown. Using the screwdriver tighten securely by hand only. INSTALL HALOGEN BULB AND GLASS Step 12. Screw the 100 Watt Halogen bulb into the socket. Do not touch the glass bulb with your fingers–it is extremely important that the glass be clean. If it is touched, or dirty, clean carefully with a tissue. A dirty glass bulb will cause the bulb to fail almost immediately. IMPORTANT! When installing the halogen bulb, carefully cut off the end of the plastic sleeve the bulb comes in and hold the bulb by the plastic sleeve to screw it into the socket. TABS HALOGEN BULB 100 WATT Step 13. Position the indentations in the outer rim of the glass shade so that they line up with the tabs on the inside surface of the fan light fixture rim. Step 14. Carefully lift the glass shade up inside the light fixture as far as it will go. GLASS GLASS SHADE SHADE Step 15. Rotate the shade in a clockwise direction until it is INDENTATION held tightly in place by the three tabs. 7 8 8 Removing Control Gently Pull the lower edge of the control out from the holder. Note: The wall anchors and 6-32 x 1” screws may be used in situations where mounting to a stud is not possible. Use the inner mounting holes. After securing the anchor, discard the anchor’s pointed screws and use the 6-32 decor ovalhead screws supplied. VERSA•TOUCH HOLDER INSTALLATION / STORAGE DECOR OVALHEAD SCREW 6-32 X 1” TOP GOES IN FIRST Wall Installation Step 1. Locate a 2x4 wall stud in a convenien...