Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
The manufacturer will not be responsible if the governing health and safety laws are not observed which permit safe and correct use of the hood and electrical connections. Before servicing or repairing the hood make sure the appliance is disconnected from the mains supply either by removing the plug or switching the power socket to OFF. CLEANING Clean the outer part of the hood with a soft cloth and liquid detergent, do not use abrasive cleaning products or scouring pads. CHANGING THE LIGHT BULB Before changing the light bulb, ensure that the appliance is not live (the switch should be in position 0 OFF). Remove the metal anti-grease filters (Fig.5). Change the halogen light using a 230V halogen light, with an E14 coupling, max. 50W. Replace the metal anti-grease filters. WARNINGS “NOTE: the areas behind the filters are not intended to be cleaned” Follow the cleaning instructions given by the manufacturer and in particular take care that there are not grease deposits on the surface of the hood which could create a possible fire hazard. Make sure the electric hob rings or gas rings are always covered when in use to avoid heating the filter. When frying never leave pans unattended as there is the risk of the oil overheating and catching fire. If reusing frying oil the fire risk is greater. Never prepare flame cooked food dishes under the hood. The air duct by the hood must not be conveyed into a flue used for other appliances that run off other energy supplies other than electricity. If the air is to be ducted, before installing make sure the flue is in good condition especially if it has been out of use for a long period of time. Always observe governing laws and regulations regarding ducting waste gases. All recommendations given must be scrupulously observed to avoid any possible fire hazard. CONTROL PANEL The control panel is situated on the front of the hood and comprises of a digital display and 6 touch control switches with the following functions: Fan ON/OFF Switch Reduces the speed of the fan (Min speed 1) 2 Digital display,displays the speed of the fan 1-6 Increases the speed of the fan (Max speed 6) OFF delay switch, press once display flashes, fan switches off automatically after 10 minutes. Light ON/OFF switch VENTILATION If there is an appliance fitted in the vicinity which requires air for combustion, additional air vents will be required to alleviate the possibility of spillage of products of combustion, from the appliance/flue while the fan is in operation. Refer to B.S. 5440 Part 2 & I.S. 813. Where such an installation exists a test for spillage should be carried out with all appliances requiring air for combustion and all extraction fans running at maximum rate, (i.e. tumble dryers, extraction fans) with all external windows and doors closed. If spillage occurs following the above operation, an additional air vent of sufficient size to prevent this occurrence should be installed. INSTRUCTIONS FOR ASSEMBLY THE MANUFACTURER WILL NOT BE RESPONSIBLE IF THESE RECOMMENDATIONS AND INSTRUCTIONS REGARDING INSTALLATION, MAINTENANCE AND USE ARE NOT OBSERVED AND RESPECTED WHEN USING THE COOKER HOOD. DIMENSIONS Fig.1 Wall Fixing Bracket The hood is designed to be wall mounted. Take the fixing brackets from the packaging and attach them to the fan unit as shown in Fig. 2 & 3. Remove the filters from the hood section as shown in (Fig. 5). Fix the hood section to the fan section using four 10mm screws (See Fig. 6). Insert the plug on the fan unit to the socket on the hood section. Position the hood in the desired position against the wall and mark the four positions for fixing the two fixing brackets. Drill four holes at the marked positions using a 6mm masonry drill bit and insert the rawl plugs into the holes. Screw the two bottom support screws half way into the rawl plugs and hook the hood assembly onto the screws. Fix the hood assembly to the wall by inserting the two top screws and tighten the bottom support screws. Attach the plastic coupling to the fan section using two 10mm screws (See Fig.4). The steel ducting for the hood is to be fixed to the wall using the bracket supplied, the bracket is to be fixed nearest the ceiling and fixed to the end of the duct with slots in it. 3 Fig.4 Fig.5 Fig.6 Fig.2 Fixing Bracket Fixing Bracket Plastic Coupling Fig.3 Fig.4 Fig.5 Fig.6 Fig.2 Fixing Bracket Fixing Bracket Plastic Coupling Fig.3 Fig.7 CONTROL PANEL 4 An AGA Company WARRANTY We undertake to repair or replace, free of charge to you any part found to be faulty within the 12 month period from the date of purchase provided that: * The fault is, in our opinion, caused by defective workmanship, or material and not by accident, misuse, neglect or normal wear and tear. * Any manufacturing defect is reported to the stockist from whom you bought the appliance within 12 months of the date of purchase. * The Waterford appliance is installed to the Manufacturer’s recommendations and by a suitably qualified perso...