Iniciar sesión:
Votos - 4, Puntuación media: 4 ( )

Manual de usuario GE Monogram, modelo ZV30 ZV36 ZV48

Fabricar: GE Monogram
Tamaño del archivo: 218.46 kb
Nombre del archivo: ceaeda7e-2589-40ff-9c8c-8b85455fe34c.pdf
Idioma del manual:enfr
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


To replace the baffles: 1. Hold the baffle at the bottom by one of the knobs . 2. Place the other end of the baffle against the inside front of the hood. 3. Slide it up and push the bottom end back until it firmly seats into place. Drip Tray Drip Tray Track Drip Tray Replacement Baffle Baffle Replacement Care and Cleaning Professional Range Hood Stainless steel Do not use a steel wool pad; it will scratch the surface. To clean the stainless steel surface, use warm sudsy water, a stainless steel cleaner such as Kleen King®, or an all-purpose liquid or spray cleaner. Always wash in the direction of the grain. Rinse thoroughly with a sponge or cloth and clean water. Dry with a soft, clean cloth. After cleaning, use a stainless steel polish, such as Stainless Steel Magic®, Revere Copper and Stainless Steel Cleaner® or Wenol All Purpose Metal Polish®. Follow the product instructions for cleaning the stainless steel surface. Light bulbs The bulbs are located on the underside of the hood. To change the light bulbs: 1. Remove the trim ring by turning it counterclockwise. 2. Grasp the bulb on the edges and remove by turning it counterclockwise. 3. Replace with the same type and size bulb. These 120 volt, 50 watt, par 16 halogen flood bulbs, with standard base, are available at specialty lighting stores. These bulbs can also be ordered from your GE supplier. Order bulb no. WB08X10028. Warming lamps The warming lamps are located on the underside of the hood. These 120 volt, 175 watt, par 38 infrared heat lamp bulbs, with standard base, are available at some specialty lighting stores. These infrared bulbs can also be ordered from your GE supplier. Order bulb no. WB08X10029. NOTE: If warming lamps are not desired, additional cooktop lighting can be obtained by replacing the infrared bulbs with standard incandescent bulbs with up to 100 watt maximum ratings, with standard bases. These bulbs are available at specialty lighting stores. The Problem Solver Professional Range Hood PROBLEM POSSIBLE CAUSE Questions? Use this problem solver! FAN AND LIGHTS DO • The hood was never electrically connected by the installer/ NOT OPERATE WHEN electrician/builder. Call the electrician/installer/builder to THE SWITCHES ARE complete the the installation. This is not covered by warranty. TURNED ON • A fuse may be blown or a circuit breaker tripped. Replace the fuse or reset the circuit breaker. THE BLOWER DOES • The blower motor wire harness was not connected or was not NOT WORK BUT THE connected properly by the installer/electrician/builder to its mating LIGHTS DO connector located inside the hood on the top surface, to the left of the blower assembly. 1. Switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. 2. Remove the filters and locate the blower wire harness connector. Is it plugged into its mating connector? 3. If no, plug the blower motor connector into its mating connector on the top of the hood. Switch the power back on. Check to see if the fan now works. 4. If no, check the circuit breaker/fuse. If it is blown/tripped, replace/reset it. Does the blower work now? If no, call GE for service. THE BLOWER FAILS • Many factors could be the root cause for reduced air-flow. TO EXHAUST THE 1. Installation could be the problem: Your hood was designed to SMOKE/STEAM/ meet specific ducting requirements. If your duct length exceeds ODORS ADEQUATELY the manufacturer's requirements, hood performance will suffer. Air-flow will also be reduced if the house duct work is too small or there are too many elbows in the system. Contact your installer or builder. 2. Obstruction in duct work could be the problem: Make sure nothing is blocking the vent (bird nests or kinks in the duct work). 3. Damper blade may not be opening. Make sure the tape is removed from the damper blades and that it swings open freely. 4. Damper blade on Wall or Roof Cap may not be opening. Contact your builder so they can make sure the damper swings open freely. 5. Dirty filters/baffles - Make sure filters (and all hood surfaces) are kept clean of grease and dirt. 6. Check to be sure the filter is clean: If replacing the filter does not correct the problem, call for service. The Problem Solver Professional Range Hood PROBLEM POSSIBLE CAUSE Questions? Use this problem solver! THE HALOGEN/ HEAT LAMP DOES NOT WORK • The lamp or socket may be defective or a wire could be disconnected. 1. Do some trouble-shooting by removing the lamp and place it in the socket of a lamp that does work (the heat lamp will fit in the halogen socket for the purpose of checking it). Does it work now? If no, the lamp is defective. If your hood is still in-warranty, call GE service and ask them to mail out a new lamp. State clearly whether you need the halogen or the heat lamp. Lamps on this produ...


Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría